What to do if my Siemens Simatic IPC647C Industrial PC does not boot or shows 'Boot device not found'?
If your Siemens Industrial PC doesn't boot or displays 'Boot device not found', it's likely that the boot device isn't the top priority in the BIOS setup or is excluded. To fix this, go to the Boot menu in the BIOS setup and change the boot priority of the boot device, or include the device in the boot priority.
Why is the external monitor dark on my Siemens Simatic IPC647C?
If the external monitor remains dark when using your Siemens Industrial PC, first ensure that the monitor is switched on. If it is, check if it's in 'power save' mode and press any key on the keyboard. Also, verify that the luminance control isn't set too low; increase the brightness. Finally, make sure both the power cord and monitor cable are properly connected to the system unit, the monitor, and a grounded outlet.
How to troubleshoot a Siemens Simatic IPC647C that is not operational?
If your Siemens Industrial PC is not operational, start by checking the power supply and ensure the power cord and connector are properly connected. Also, verify that the device is operating within the specified environmental conditions. If the device was shipped in cold weather, wait approximately 12 hours before switching it on.
What to do if a USB device is not responding on Siemens Simatic IPC647C?
If a USB device is not responding on your Siemens Industrial PC, try using a different USB port or enabling the port in the BIOS settings. If you're using a USB 2.0 device, make sure USB 2.0 is enabled in the BIOS.
Why doesn't the mouse pointer appear on my Siemens Industrial PC?
If the mouse pointer does not appear on the screen of your Siemens Industrial PC, ensure the mouse driver is properly installed and present when you start the application program. Also, check whether the mouse cord is properly connected to the system unit and that any adapters or extensions on the mouse cable are securely connected.
Why does the screen flicker on my Siemens Industrial PC?
If the screen flickers when the mouse moves or when programs are called on your Siemens Industrial PC, it may be due to missing DDC information. To resolve this, use a monitor that supports DDC, a KVM switch that passes through DDC information, or a basic cable adapter with DVI-I to VGA connector.
What to do if the DVD/CD front loader on my Siemens Simatic IPC647C doesn't open?
If the front loader on your Siemens Industrial PC DVD/CD drive doesn't open, it may be because the device is switched off or the open/close button is disabled by software. To manually remove the data medium, switch off the device, then insert a pointed object (like a pin or opened paper clip) into the emergency extraction opening of the drive. Apply slight pressure until the front loader opens, then pull the loader further out.
How to fix boot from RAID array after hard disk change on Siemens Simatic IPC647C?
If, after changing the hard disk on your Siemens Industrial PC, the system does not boot from the RAID array, set the RAID array to be first in the boot priority order.
What does 'unused' SATA port mean after hard disk change on Siemens Industrial PC?
If, after changing the hard disk on your Siemens Industrial PC, 'unused' is indicated for the relevant SATA port, reboot the system with a functioning hard disk. This issue may occur if the system was booted without a functioning hard disk, possibly because the removable rack was not switched on.
How to correct the time and date on a Siemens Simatic IPC647C Industrial PC?
To correct an incorrect time and/or date on your Siemens Industrial PC, press during the boot sequence to enter BIOS Setup and adjust the time and date settings.
Details critical safety warnings and legal compliance for device operation.
Describes the integrated monitoring and diagnostic functions of the device.
Lists detailed general, design, enclosure, drive bay, and slot features.
Details optional installation locations and mounting methods for the device.
Provides notes and precautions before connecting external peripherals to the device.
Explains how to safely connect the device to the mains power supply.
Outlines necessary preparations and notes before putting the device into operation.
Details the procedure for the first-time setup of the operating system.
Describes options for integrating the PC into existing or planned system environments.
Details the PROFINET interface and related documentation for industrial Ethernet.
Explains how temperature is monitored and potential causes of errors.
Covers procedures for repairs, preventive maintenance, and replacement of hardware components.
Provides procedures for reinstalling software, drivers, and updating the OS.
Lists POST codes relevant to users, their meaning, description, and remedy.
Details on-screen error messages during the boot process and their troubleshooting.
Offers tips for localizing and troubleshooting common operational problems.
Provides comprehensive technical data on the device's general specifications and standards.
Covers BIOS Setup overview, starting, menus, and specific configurations.
General| Type | Industrial PC |
|---|---|
| Processor | Intel Core i7 |
| Chipset | Intel Q170 |
| Operating System | Windows 10 IoT Enterprise |
| Ethernet | 2 x Gigabit Ethernet |
| Protection Class | IP20 |
| Power Supply | 100-240 V AC, 50-60 Hz |
| Operating Temperature | 0°C to 50°C |
| Relative Humidity | 5 to 85% (non-condensing) |
| Display | No integrated display |
| Ports | DisplayPort |
| Serial Ports | 2 x RS232/422/485 |
| Slots | 2 x PCIe x16, 1 x PCIe x4, 4 x PCI |
To Next Page
