EasyManuals Logo

Siemens SIMOTICS S-1FT7 User Manual

Siemens SIMOTICS S-1FT7
408 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #97 background imageLoading...
Page #97 background image
Motor components and options
4.2 Options
S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA
95
Table 4- 7 Rotation range of the round connector M17
Motor
Round connector M17
Drawing
Angle α´
Angle β´
1FT703
1FT704
125° 130°
1FT706
115°
110°
1FT708
105°
100°
1FT710
1FT713
95°
95°
The motor is 5 mm longer and has the same overall length as the motor without a DRIVE-
CLiQ interface.
The height of the obstructing contour from the center of the motor is 82 mm.
Connection requires a signal cable that deviates from the standard.
Additional information is provided at Product notification SIMOTICS S with option N16
(https://support.industry.siemens.com/cs/document/58657336
).
Additional information on DRIVE-CLiQ signal cables with round connector M17 at the motor
end is available at DRIVE-CLiQ cables for motors equipped with option N16
(https://support.industry.siemens.com/cs/document/109478937
).
Limited availability
Option N16 is only available for the following naturally cooled and water-cooled 1FT7 motors.
1FT7☐☐☐-5A☐☐☐-1
B
☐☐-Z
1FT7☐☐☐-5A☐☐☐-1C☐☐-Z
1FT7☐☐☐-5A☐☐☐-1K☐☐-Z
1FT7☐☐☐-5A☐☐☐-1L☐☐-Z
1FT7☐☐☐-5A☐☐☐-1M☐☐-Z
1FT7☐☐☐-5W☐☐☐-1
B
☐☐-Z
1FT7☐☐☐-5W☐☐☐-1C☐☐-Z
1FT7☐☐☐-5W☐☐☐-1K☐☐-Z
1FT7☐☐☐-5W☐☐☐-1L☐☐-Z
1FT7☐☐☐-5W☐☐☐-1M☐☐-Z
Option N16 is only available in combination with the following encoders:
Encoder AS24DQI (DRIVE-CLiQ absolute encoder 24 bit singleturn)
Encoder AM24DQI (DRIVE-CLiQ absolute encoder 24 bit + 12 bit multiturn)
Encoder AM2048S/R (absolute encoder 2048 S/R, 4096 revolutions multiturn, with EnDat
interface)
Option N16 is only available for motors with rotatable connector (connector size 1 and 1.5).
Option N16 is not available for 1FT7 motors SH132.
Cleaning recommendation
Cleaning recommendations for motors equipped with option N16 are provided in Product
notification SIMOTICS S with option N16
(https://support.industry.siemens.com/cs/document/58657336
).

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SIMOTICS S-1FT7 and is the answer not in the manual?

Siemens SIMOTICS S-1FT7 Specifications

General IconGeneral
BrandSiemens
ModelSIMOTICS S-1FT7
CategoryEngine
LanguageEnglish

Related product manuals