To Next PageTo Next Page
Why do Siemens Sitrans F show a Flow Overload?
If your Siemens Measuring Instruments report a 'Flow Overload', it's likely that the flow sensor is too small for the current installation. Make sure the meter sizing is appropriate for your setup. The alarm will remain active until the flow issue is corrected.
What causes a Leakage alarm in Siemens Sitrans F?
If your Siemens Measuring Instruments display a 'Leakage' alarm, it indicates a leakage in the water network. You should check the settings and pipe installation. The alarm can be manually reset using parameter 208, which also resets the leakage period information (parameter 820).
How to troubleshoot an Insulation fault in Siemens Sitrans F Measuring Instruments?
If your Siemens Measuring Instruments displays an 'Insulation fault', it could be due to several reasons: defect cables between sensor and transmitter, wrong connections of remote cables, water between coils and electrodes (possibly from a broken liner), or pollution/moisture on the PCB from water in the encapsulation. Check the cable and wiring installation, as well as the surrounding area for any disturbances. Reactivating the insulation test (parameter 800) will reset the alarm and start a new test. Measurement is disabled during the 4-minute test, and the alarm remains active until a new test period detects no failures.
What does 'Database checksum' mean on Siemens Measuring Instruments?
If Siemens Measuring Instruments display shows 'Database checksum', it's likely due to a power failure during the EEPROM write process. First, reset the checksum repair alarm using parameter 560 and check the data. If the data is incorrect or the checksum error recurs, replace the PCB board. The alarm remains active until the fault is corrected.
How to fix a Coil current fault on Siemens Measuring Instruments?
If your Siemens Measuring Instruments display a 'Coil current fault', it indicates that the coils have been disconnected, possibly due to broken cables or wires. Inspect the cable and wiring installation. The alarm will remain active until the fault is resolved.
What to do if Siemens Sitrans F display 'Empty Pipe'?
If Siemens Measuring Instruments shows 'Empty Pipe', it means the pipe is not filled with water. Make sure the sensor is completely filled with water. The alarm remains active until the issue is resolved.
How to resolve PulseA overload on Siemens Sitrans F?
If your Siemens Measuring Instruments display shows 'PulseA overload', it means there are incorrect settings for output A. You should change the volume per pulse to a higher value, referring to the technical data on page 98 for pulse selection. Keep in mind that Pulse A is limited to 100Hz. The alarm will remain active until the output pulse rate drops below the maximum.
What causes Amplifier overload in Siemens Sitrans F Measuring Instruments?
If your Siemens Measuring Instruments show 'Amplifier overload', it indicates that the electrodes have been disconnected or connected to ground. Check the cable and wiring installation. The alarm remains active until the fault is corrected.
What does Consumption Interval mean on Siemens Sitrans F?
If your Siemens Measuring Instruments display a 'Consumption Interval' alarm, it suggests that the flow rate is either higher or lower than expected, or there's a wrong parameter setup. Check the data logger values and consumption limit. This alarm must be manually reset via parameter 209.
Why do Siemens Sitrans F show a Low Impedance alarm?
If your Siemens Measuring Instruments displays 'Low Impedance', it suggests that the water is polluted, for example, saltwater mixed with fresh water. The alarm will remain active until the water resistance rises above the low media alarm limit.
General| Measurement Principle | Coriolis, Electromagnetic, Ultrasonic |
|---|---|
| Communication Protocols | HART, PROFIBUS, Foundation Fieldbus, Modbus |
| Pressure Range | Varies by model (e.g., up to 400 bar for some models) |
| Power Supply | 24 V DC or 110-230 V AC |
| Protection Class | IP67, IP68 |
| Housing Material | Stainless steel, aluminum |
| Liner Material | PTFE, PFA, rubber |
| Electrode Material | Stainless steel, Hastelloy, platinum |
Explains the scope and target audience of the operating instructions.
Details the changes made in previous editions of the documentation.
Lists compatible versions of device integration packages for different manual editions.
Describes the contents of the user documentation package for the product.
Lists the components delivered with the device.
Provides guidance on industrial security functions and cyber threat protection.
Details requirements for proper transport and storage to ensure device protection.
States that manual content does not modify warranty conditions and reserves the right to technical changes.
Outlines essential conditions and precautions for maintaining safe operation.
Lists safety rules and laws applicable during connection, assembly, and operation.
Describes the transmitter's modular design, components, and availability.
Highlights key features such as Modbus connectivity, local display, and housing options.
Lists various industries and applications where the flowmeter can be used.
Provides information on general purpose and hazardous area approvals.
Details the device's support for the Modbus communication protocol.
Specifies requirements for installation location based on enclosure rating and environmental factors.
Provides step-by-step instructions for mounting the transmitter on a wall.
Covers essential safety precautions for connecting the device, including grounding.
Explains how to integrate the device into a Modbus RTU network.
Details the wiring requirements for Modbus RTU RS 485 bus systems.
Highlights safety precautions related to opening the device and general requirements.
Guides through the initial device setup process, including language, date, and time.
Introduces the wizards available for guided device configuration.
Details the steps for the Quick commissioning wizard for essential application parameters.
Guides through the configuration of essential sensor parameters.
Explains the setup of process values and measurement views.
Guides through the setup of inputs and outputs on available channels.
Provides guidance on configuring the communication interface.
Describes how to operate the device using the local HMI interface.
Explains the access level control for parameters via the HMI menu.
Details how to display current process values using various view types.
Explains how to access and operate the totalizer functions.
Describes how to view and manage active alarms.
Highlights safety precautions regarding device repair and explosion protection.
Information on recalibration services offered by Siemens Flow Instruments.
Provides instructions for cleaning the device enclosure.
Details periodic inspection requirements and checks for device integrity.
Specifies the procedure and part number for replacing the on-board battery.
Describes the first step in troubleshooting by observing the HMI display for alarms.
Provides an overview of potential symptoms, diagnostics, causes, and remedies.
Explains how to use a test block for bench testing transmitter, sensors, and cables.
Provides inspection steps to identify issues when the flowmeter is unable to measure flow.
Details how to verify sensor diagnostic parameters and view receiver signals.
Lists alarms, system messages, and their corresponding causes and corrective actions.
Provides specifications for supply voltage, power consumption, and environmental conditions.
Details Modbus communication parameters such as protocol version and transmission rate.
Specifies technical data for digital and current inputs on channels 3 and 4.
Provides technical data for current and digital outputs on various channels.
Details the device design, materials, ingress protection, and mechanical load specifications.
Specifies ambient temperature, climate class, altitude, and EMC performance.
Lists ATEX, IECEx, and FM approvals for the device.
Provides mechanical dimensions for the wall mount housing transmitter.
Explains how devices are mapped to the Modbus address space for read/write access.
Details general Modbus communication settings like baud rate and parity.
Describes the configurable coil definitions for Modbus communication.
Explains the possibility to remap parameters to chosen Modbus registers.
Details how to adjust the byte order for integer values in Modbus messages.
Details how to adjust the byte order for floating-point values in Modbus messages.
Lists general Modbus function codes and their descriptions.
Manages Modbus master access to device parameters based on PIN information.
Provides a comprehensive list of Modbus RTU holding registers for SITRANS FS430.
Lists Modbus registers for process values for standard applications.
Details Modbus registers for totalizer settings.
Describes Modbus units settings for values and quantities communicated via Modbus.
Provides general sensor settings for clamp-on applications.
Specifies settings related to pipe dimensions and material for clamp-on sensors.
Details parameters for compensating upstream and downstream pipe geometry.
Lists characteristics of process media such as sound velocity and temperature.
Provides recommended sensor spacing methods and distances for clamp-on sensors.
Details settings specific to path 1, including sensor frequency and path geometry.
Explains user calibration parameters like slope correction factor and path offsets.
Provides commands to start automatic factory or user zero offset adjustments.
Details settings for multipoint calibration, including function and protection.
Information on where to find device certificates online and on the documentation disk.
Contact information and resources for technical assistance.
Overview of SIMATIC PDM software for commissioning and maintenance.
Lists functionalities of SIMATIC PDM for monitoring, adjusting, and simulating device data.
Specifies compatible SIMATIC PDM versions for the device's EDD.
Outlines the steps for ensuring proper connection of SIMATIC PDM.
Guides on integrating Electronic Device Descriptions (EDD) into SIMATIC PDM.
Details the process of adding a device to the SIMATIC Modbus network within PDM.
Steps for configuring a new device, including EDD check and parameter upload.
Describes the Quick Start Wizard for easy multistep device configuration.
Guides through the necessary steps to install sensors for clamp-on configuration.
Explains performing the Zero Point Adjustment wizard to remove residual zero offset.
Details how to adjust parameter values using SIMATIC PDM's online menus.
Lists parameters accessible through Device, View, or Diagnostics drop-down menus.
Describes how to view process values, totalizers, and loop current in real time.
Explains how to monitor the trend of process values using the Trend view.
