How to fix display and LED-signals of the SKF Maxilube Water Pump user interface if they are not lit?
If the display and LED-signals of the SKF Maxilube Water Pump user interface are not lit, it indicates that there is no supply voltage at the pumping center. Check the supply voltage.
Why the green LED-signal POWER and the user interface of the SKF MAX-1-2-24-X-R-V2 control center are not lit?
If the green LED-signal POWER and the user interface of the SKF Water Pump control center are not lit, it could be that the main switch of the control center is in the OFF-position, or the fuse has operated. Turn the main switch to the ON-position and check the fuse.
What to do if the SKF MAX-1-2-24-X-R-V2 Water Pump starts but the pressure does not rise?
If the SKF Water Pump starts, but the pressure doesn't rise, the grease filter may be clogged, there may be air in the suction piping of the pump or there may be impurities in the suction head of the pump. You can clean or replace the grease filter cartridge. Remove air from the pump by opening the venting screw of the grease filter or the pressure connection of the pump, ensuring that only grease (not air) comes out.
Why does the SKF MAX-1-2-24-X-R-V2 Water Pump start but the pressure does not rise?
If the SKF Water Pump starts but the pressure doesn't rise, the pressure air level might not be high enough. Check that the pressure at the pressure air regulator is 3,5-4,5 bar and inspect the pressure air supply piping for leaks.
What to do if the SKF Water Pump does not start?
If the SKF Water Pump doesn't start, it could be due to several reasons: the pressure air supply might be closed, the pressure air level might not be high enough, or the supply voltage might be off. To resolve this, turn on the pressure air supply by pressing down the shut-off valve button or set the air pressure to 3,5-4,5 bar using the pressure regulator and the pressure gauge. Also, check that the pressure at the pressure air regulator is 3,5-4,5 bar. Inspect the pressure air supply piping for leaks. Ensure the LED-signal of the pump is lit, the supply voltage is on, and the M12 cable is correctly connected and in good condition.
What to do if the SKF MAX-1-2-24-X-R-V2 Water Pump user interface displays alarm for high pressure in a lubrication channel?
If the user interface displays an alarm for high pressure in a lubrication channel for the SKF Water Pump, and the pressure at the pressure control unit is above the set pressure low limit value when pressurization starts, the control valve at the hydraulic part may not be operating. Replace control cartridge CHV-100 when necessary.
What to do if there is considerable grease leakage at the lubrication point of the SKF MAX-1-2-24-X-R-V2?
If you observe considerable grease leakage at the lubrication point and the bearing temperature rises in your SKF Water Pump, it suggests that the lubrication cycle has been set too short. Check the correct lubrication cycle at the doser setting table of the lubrication system in question.
What does it mean if the SKF Water Pump user interface displays lubricant low level alarm in a lubrication channel?
If the user interface of your SKF Water Pump displays a lubricant low level alarm in a lubrication channel, this indicates that the lubricant barrel is empty. Replace the lubricant barrel and then reset the alarm.
General| Brand | SKF |
|---|---|
| Model | MAX-1-2-24-X-R-V2 |
| Category | Water Pump |
| Language | English |
Guidelines for safe operation and handling of the product.
Rules for safe operation, emphasizing caution and proper use.
Steps for initial setup and daily operational readiness.
Procedure for immediate shutdown in emergency situations.
Describes the automated process of the pumping centre.
Covers safe practices for handling, setup, and upkeep.
Steps for initial setup and verification of the system.
Step-by-step guide for changing the lubricant barrel.
Details of the standard operating mode of the IF-105.
Describes the various functions available in normal mode.
Overview of system alarms and their indications.
Details the alarm for low lubricant level.
Details pressure alarms for MonoFlex/DuoFlex systems.
Details pulse alarms specific to ProFlex systems.
Alarm triggered by SKF Doser monitor status.
Alarm from the air pressure switch of the grease spray system.
Details specific malfunctions and their causes.
Provides a table for diagnosing and resolving operational malfunctions.
To Next Page
