Slayer STEAM EP - Barista Dashboard Volumetrics

SLAYER STEAM EP USER MANUAL V1.1 | SEPTEMBER 11, 2018 26
via the Copy to All Groups YES/NO feature.
The volumetrics are measured by a number that is related to the
flowmeter revolutions, but is custom made to allow easy shot adjustments
after the setting have been stored. Setting parameters can be set as low as
20 and up to 1000. M for Manual is also an option.
Programming your volumetrics is intuitive and easy. Grab a scale, your
favorite coee and an open mind to creating the best tastes your espresso
has to oer! The buttons are programmable to a numerical value between
20 and 1000 with each click representing approximately 0.5 grams
of espresso output. A step by step guide to setting your Volumetrics,
Temperatures and Pre-Wet are outlined in the steps below.
1. Scroll to the title screen, Brew Volume Program Dose and depress the
menu button.
SCREEN EXAMPLE:
Brew Volume
Program Dose
2. Select this button by depressing. The screen will again prompt a
button selection.
SCREEN EXAMPLE:
Brew Volume
Choose Button
3. All Brew buttons will blink, prompting the user to select a button for
programming.
4. Select the brew button to adjust and depress. A lit button is now
ready for a value.
5. “Brew Volume <###>” displayed on the screen is the current value
for volume.
6. Dose coee into the portafilter and press the same button again to
start the brewing process depress to stop the flow at the desired
result.
• Typically, when setting volumetrics with a scale, there is marginal
human error of 2-3 grams when fumbling with multiple moving
parts. Before saving the value shared by the flowmeter, turn the
menu button up or down to adjust to your desired result (each
number will add/subtract about .5 grams of espresso.
7. A new volumetric has been set. Depress the menu button to save your
volumetric value.
8. When working from the LEFT farthest group an option to Copy All
Groups will prompt you to select YES or NO If you select yes it will
copy that buttons value to the same button on the other groups.
9. At this point all brew button lights will blink again prompting the user
to select the next button and program a value.
10. Follow this process for all remaining buttons.
11. When volumetric programing is complete exit the menu by pressing
and holding the menu button for 2 seconds to continue setup in the
Manager menu, or 5 seconds to return to the Home screen.
NOTE: If there is a 1-3 gram dierence in the final output of your group
heads volumetrics and proper technique has been used for dialing in a
shot (ie; using a scale and an exacting coee recipe), verify the machine
flowmeters are calibrated. For a step by step guide toward calibrating your
flowmeters for optimum consistency, turn to page #34.
PROTIP: Quickly program any brew button to manual (M) by selecting a
button to program, then quickly turn it o. The value will show M as the
programmed value.
Volumetric Adjustments
After manually programming a volumetric dose, you may want to slightly
increase or decrease the dose based on the taste. This is now easily
achievable by slightly adjusting the Volumetric in the Brew Volume
Choose Button screen.
SCREEN EXAMPLE:
Brew Volume
Choose Button
1. While in the Manager menu, turn the button clockwise to increase the
volume and counter clockwise to decrease. each number is roughly .5
grams of espresso.
2. Depress the button to save your setting.
3. If you are working from the LEFT group, an option to Copy All Groups
will prompt you to select YES or NO.
4. Choose and press the menu button to save the value across all groups
on the corresponding button.
5. Select NO to individually set each volumetric value.
SCREEN EXAMPLE: LEFT GROUP
Brew Volume 240
All Groups <YES>
Once the value is saved all button lights will blink, prompting you to select
the next button to program volumetric values.