HCD-SHAKE7
13
SECTION 3
STORM TEST MODE
[PANEL TEST MODE]
This mode is used to check the fl uorescent indicator tube, LEDs,
keys, [VOLUME / DJ CONTROL] jog, model, destination and
software version.
Procedure:
1. Press [ENTER] and [MUSIC] button simultaneously and hold
3 seconds.
2. All LEDs and segments in fl uorescent indicator tube are light-
ed up. All RGB LEDs are lighted up in white color.
3. When you want to enter to the software version display mode,
press [+ / ] button.
The model information appears on the fl uorescent indicator
tube.
• “STORM” is shown for SHAKE-7.
** If display shown information below, please proceed with
[MODEL & DEST WRITE MODE] to write model & destina-
tion.
• “STORM(T)” is shown for SHAKE-7.
Press [+ / ] button again to view the destination informa-
tion.
4. During the destination information display, press [+ / ]
button. Each time [+ / ] button is pressed, the fl uorescent
indicator tube shows the version of each category software in
the following sequence: SC, MTK, UI, PF, SYS, CD, CDMA,
CDMB, ST, TA, TAS, TM, BTM, BT, NFC, and return back to
model information display.
5. When [] button is pressed while the version numbers
are being displayed except model and destination, the
date of the software creation appears. When [] button
is pressed again, the display returns to the software ver-
sion display.
6. Press [- / ] button, the key check mode is activated.
7. In the key check mode, the fl uorescent indicator tube displays
“K 0 V0”.
• Each time a button is pressed, “K” value increases.
However, once a button has been pressed, it is no lon-
ger taken into account.
• “V” value increases in the manner of 0, 1, 2, 3... if
[VOLUME / DJ CONTROL] knob is turned clock-
wise, or it decreases in the manner of 0, 9, 8, 7... if
[VOLUME / DJ CONTROL] knob is turned counter-
clockwise.
8. When [ENTER] button is pressed after all LEDs and segments
in fl uorescent indicator tube light up, alternate segments in
fl uorescent indicator tube and LEDs would light up, all RGB
LEDs would light up in red color. If you press [ENTER] but-
ton again, another half of alternate segments in fl uorescent in-
dicator tube and LEDs would light up, all RGB LEDs would
light up in green color. Pressing [ENTER] button again would
cause all segments in fl uorescent indicator tube and LEDs light
up, all RGB LEDs would light up in blue color. Pressing [EN-
TER] button again would turn off all segments in fl uorescent
indicator tube and all LEDs including RGB LEDs.
9. To release from this mode, press the buttons in the same man-
ner as step 1, or disconnect the power cord.
[MODEL & DEST WRITE MODE]
This mode is used to set software model & destination.
This mode is only available when no permanent model & destina-
tion is stored.
Procedure:
1. Press [ENTER] and [FOOTBALL] button simultaneously and
hold for 5 seconds.
2. Fluorescent indicator tube display will show “M XXXXX”.
3. Press [+ / ] button to select the model based on the set’s
model.
Product Code F. Tube display
STORM “M STORM”
4. Press [ENTER] button.
5. Fluorescent indicator tube display will show “D XXXXX”.
6. Press [+ / ] button to select the destination based on the
set’s country.
Area Code Country F. Tube display
J1 Japan “D J”
JE1 Tourist “D JE”
U2/CA2 America, Canada “D NA”
CEL/CE1/
CE2
Europe (general) “D CE2”
CEK U.K. “D CEK”
RU1/RU3 Russia “D RU”
AU1 Australia “D AU”
CN1 China “D CN”
E12 India, Pakistan, Morocco “D E12”
E3/E93/
SA2/E15
Middle East, Africa
(South Africa), Iran
“D E3”
E4 Africa “D E12”
EA3 Saudi Arabia “D EA3”
HK1/
HK2/PL1/
SP1/SP2/
SP6/TH1
Hong Kong, Philippines,
Singapore, Malaysia,
Thailand
“D ASIA”
KR2 Korea “D KR”
TW2 Taiwan “D TW”
E2, E32,
E51, AR2
Latin America (general),
Chile, Peru, Argentina
“D LATIN”
BR1 Brazil “D BR”
MX2,
MX4
Mexico “D MX”
7. Press [ENTER] button to confi rm the selection.
8. “RESET” appears on the fl uorescent indicator tube. After that,
the fl uorescent indicator tube becomes blank for a while, and
the system is reset.
9. Perform [PANEL TEST MODE] again to confi rm on the mod-
el & destination.
To Next Page
Loading...
