Studer RCC-02 - Reference

To Next Page

To Previous Page

Reference

This document applies to versions of firmware release R542 or higher of the remote control.

If any doubt about your software version, you can check it with the menu « Information on the

system » page 76.

Main Page

Default Chapter5
- Table of Contents5
1 Foreword9
- Conventions9
- Product Recycling9
- EC Declaration of Conformity10
- Studer Innotec Contact Details10
- Your Reseller Contact Details10
2 Warnings and Caution11
- Warranty11
- Limitation of Responsability11
- Safety Instructions11
- Acceptance of the Software Licence and Updates11
- Compatibility12
- Access Code for Extended Functions12
3 Introduction13
- Models Concerned13
- Controls and Indicators13
- SD Card14
4 Connection15
- Series Connection15
5 Dimensions19
6 Quick Start Guide20
- Setting of the Language20
- Adaptation to the Source20
- Adaptation to the Battery21
- Activation of the Function Smart-Boost22
7 Basic Displays23
8 Activating and Deactivating the Combi Xtender24
9 Quick Setting of the Maximum Source AC Current24
10 Setting of the RCC Remote Control25
- Setting of the Language {500025
- Other Languages {503625
- Setting of Time {5001} and Date {500226
- User Level {501226
- Drive the Remote Control to the User Level Basic {501926
- INSTALLER - Modification of the Xtender Parameters Thresholds Together {504226
  - Force All Xtender Parameters to Threshold {504326
  - Restore the Default Thresholds of the Xtender Parameters {504426
- Data Logger {505727
  - Data Logger Enabled {510127
  - Backup of the Current Day Data {505927
- Backup and Restoring {501327
- Adjusting the Contrast29
- Back-Lighting {500729
- Extended and Special Functions {502129
11 Information on the Operating Mode of the Installation31
- Display of the Parallel and Three-Phase Systems33
12 Messages and Account of Events34
- 000) Warning: Battery Voltage Low34
- 003) AC-In Synchronization in Progress34
- 004) Input Frequency AC-In Wrong35
- 006) Input Voltage AC-In too High35
- 007) Input Voltage AC-In too Low35
- 008) Halted: Inverter Overload SC35
- 014) Halted: over Temperature el35
- Halted: Inverter Overload BL36
- 016) Warning: Fan Error Detected36
- 018) Warning: Excessive Battery Voltage Ripple36
- 019) Halted: Battery under Voltage36
- 020) Halted: Battery Overvoltage36
- 021) Input Limit Reached, no Transfer36
- 022) Error: Voltage Presence on AC-Out37
- 023) Error: Inverter Phase Not Defined37
- Check the Clock Battery37
- 041) Warning: Overtemperature TR37
- 042) Halted: Unauthorized Energy Source at the Output37
- 058) Error: Synchronization with Master Lost37
- 059) Halted: Inverter Overload HW37
- Warning: Time Security for Auxiliary Contacts38
- 062) Warning: Genset, no AC-In Coming after AUX Command38
- Stored Events38
13 Data Logging39
- Functioning39
- Analysis and Visualization of the Data with the XTENDER Data Analysis Tool39
14 Setting of the Xtender40
- General40
- Configuration on a System with Several Xtenders40
- Utilisation and Access Levels40
- Pre-Defined Functions of the Auxiliary Relays40
- Access to the Parameters41
  - Access to a Parameter by Its Number41
  - Access to a Parameter Via the Menu41
- INSTALLER - Utilisation and Access Levels42
- Basic Settings {110042
- Management and Battery Cycle {113746
- Inverter {118656
- AC-In and Transfer {119760
- Configuration of Auxiliary Contacts 1 and 2 {1201} {131064
- Auxiliary Contacts 1 and 2 Extended Functions {148971
- System {110172
- Multi Xtender {128275
- Grid-Feeding {152277
15 Information on the System80
- Remote Controls80
- Xtender80
16 Software(S) Updating81
- Updating Process81
17 Application Examples82
- General Use: Inverter, Charger with Grid82
- Use of a Limited Power Source82
- Use to Increase the Power on an Existing Installation83
- Load Shedding of the Second Priority Loads83
18 Appendices84
- Appendix 1: List of Configuration Interdependencies84
19 Parameter Tables85
- Remote Control Parameters85
- Inverter Parameters87
20 Parameter Index {XXXX99

Studer RCC-02 - Reference

Table of Contents

Other manuals for Studer RCC-02