Studer RCC-02 - Page 4

104 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Default Chapter5
- Table of Contents5
1 Foreword9
- Conventions9
- Product Recycling9
- EC Declaration of Conformity10
- Studer Innotec Contact Details10
- Your Reseller Contact Details10
2 Warnings and Caution11
- Warranty11
- Limitation of Responsability11
- Safety Instructions11
- Acceptance of the Software Licence and Updates11
- Compatibility12
- Access Code for Extended Functions12
3 Introduction13
- Models Concerned13
- Controls and Indicators13
- SD Card14
4 Connection15
- Series Connection15
5 Dimensions19
6 Quick Start Guide20
- Setting of the Language20
- Adaptation to the Source20
- Adaptation to the Battery21
- Activation of the Function Smart-Boost22
7 Basic Displays23
8 Activating and Deactivating the Combi Xtender24
9 Quick Setting of the Maximum Source AC Current24
10 Setting of the RCC Remote Control25
- Setting of the Language {500025
- Other Languages {503625
- Setting of Time {5001} and Date {500226
- User Level {501226
- Drive the Remote Control to the User Level Basic {501926
- INSTALLER - Modification of the Xtender Parameters Thresholds Together {504226
  - Force All Xtender Parameters to Threshold {504326
  - Restore the Default Thresholds of the Xtender Parameters {504426
- Data Logger {505727
  - Data Logger Enabled {510127
  - Backup of the Current Day Data {505927
- Backup and Restoring {501327
- Adjusting the Contrast29
- Back-Lighting {500729
- Extended and Special Functions {502129
11 Information on the Operating Mode of the Installation31
- Display of the Parallel and Three-Phase Systems33
12 Messages and Account of Events34
- 000) Warning: Battery Voltage Low34
- 003) AC-In Synchronization in Progress34
- 004) Input Frequency AC-In Wrong35
- 006) Input Voltage AC-In too High35
- 007) Input Voltage AC-In too Low35
- 008) Halted: Inverter Overload SC35
- 014) Halted: over Temperature el35
- Halted: Inverter Overload BL36
- 016) Warning: Fan Error Detected36
- 018) Warning: Excessive Battery Voltage Ripple36
- 019) Halted: Battery under Voltage36
- 020) Halted: Battery Overvoltage36
- 021) Input Limit Reached, no Transfer36
- 022) Error: Voltage Presence on AC-Out37
- 023) Error: Inverter Phase Not Defined37
- Check the Clock Battery37
- 041) Warning: Overtemperature TR37
- 042) Halted: Unauthorized Energy Source at the Output37
- 058) Error: Synchronization with Master Lost37
- 059) Halted: Inverter Overload HW37
- Warning: Time Security for Auxiliary Contacts38
- 062) Warning: Genset, no AC-In Coming after AUX Command38
- Stored Events38
13 Data Logging39
- Functioning39
- Analysis and Visualization of the Data with the XTENDER Data Analysis Tool39
14 Setting of the Xtender40
- General40
- Configuration on a System with Several Xtenders40
- Utilisation and Access Levels40
- Pre-Defined Functions of the Auxiliary Relays40
- Access to the Parameters41
  - Access to a Parameter by Its Number41
  - Access to a Parameter Via the Menu41
- INSTALLER - Utilisation and Access Levels42
- Basic Settings {110042
- Management and Battery Cycle {113746
- Inverter {118656
- AC-In and Transfer {119760
- Configuration of Auxiliary Contacts 1 and 2 {1201} {131064
- Auxiliary Contacts 1 and 2 Extended Functions {148971
- System {110172
- Multi Xtender {128275
- Grid-Feeding {152277
15 Information on the System80
- Remote Controls80
- Xtender80
16 Software(S) Updating81
- Updating Process81
17 Application Examples82
- General Use: Inverter, Charger with Grid82
- Use of a Limited Power Source82
- Use to Increase the Power on an Existing Installation83
- Load Shedding of the Second Priority Loads83
18 Appendices84
- Appendix 1: List of Configuration Interdependencies84
19 Parameter Tables85
- Remote Control Parameters85
- Inverter Parameters87
20 Parameter Index {XXXX99

Other manuals for Studer RCC-02

Quick Guide44 pages

Reference Guide2 pages