Synrad 48 Series - Operation

88 pages

To Next Page

To Previous Page

operation

Synrad

Series 48Series 48

Series 48 operator’s manual

Use information in this section to familiarize yourself with Series 48 controls and indica-

tors and to begin operating your laser.

This section contains the following information:

■ Controls and indicators – displays and describes exterior controls and indicators on

Series 48 Keyswitch and OEM lasers.

■ Initial start-up – explains how to start your Series 48 laser while verifying proper

operation.

Main Page

Table of Contents5
Terms11
General Hazards11
48-1 Label Locations14
Figure 1 48-1 Hazard Label and CE Label Locations14
Figure 2 48-2 Hazard Label and CE Label Locations15
48-5 Label Locations16
Figure 3 48-5 Hazard Label and CE Label Locations16
Agency Compliance17
Center for Devices and Radiological Health (CDRH) Requirements17
Federal Communications Commission (FCC) Requirements18
European Union (EU) Requirements19
Table 1 Class IV Safety Features20
Figure 4 European Compliance Mark21
Table 2 European Union Directives21
Declaration of Conformity22
Getting Started23
Introduction24
Series 48 Nomenclature24
Unpacking25
Incoming Inspection25
Packaging Guidelines25
Inventory26
Figure 1-1 Series 48 Shipping Box Contents26
Table 1-1 Ship Kit Contents26
Contents Description27
Mounting28
Standard Mounting28
With an FH Series Marking Head28
Connecting29
Air-Cooled Connections29
Figure 1-2 48-1 / 48-2 Cooling Fan Placement29
Water-Cooled Connections30
Table 1-2 Dew Point Temperatures31
Figure 1-3 48-1 / 48-2 Cooling Connections32
Figure 1-4 48-5 Cooling Connections33
Electrical Connections34
Figure 1-5 DC-1 (Astec) Power Supply34
Figure 1-6 DC-2/DC-5 (Power-One) Power Supplies35
Control Connections36
DB9 Connections37
Figure 1-7 Typical Series 48 System Interconnection Diagram38
Operation39
Controls and Indicators40
Initial Start-Up42
With a UC-2000 Controller42
Without a UC-2000 Controller44
Technical Reference47
Technical Overview48
Introduction48
Figure 3-1 Average Laser Output Vs. Percent PWM Duty Cycle48
Plasma Section49
Optical Resonator49
Technical Reference49
Figure 3-2 Cross Section of Tube49
Control Circuitry50
Figure 3-3 Beam Characteristics50
Optical Setup53
Figure 3-5 "Flying Optics" Beam Path53
Table 3-1 Gas Purity Specifications54
Controlling Laser Power55
Control Signals55
Figure 3-7 Series 48 Waveforms56
Operating Modes57
Figure 3-8 PWM Command Signal Waveform57
Table 3-2 PWM Command Signal Levels58
DB9 Connections60
Figure 3-9 Factory-Installed DB9 Jumper Plug Wiring60
Table 3-3 Remote Keyswitch and Remote Interlock Signal60
Table 3-4 DB9 Pin Assignments61
Integrating Series 48 Safety Features62
Keyswitch Functions62
Remote Interlock Functions63
Series 48 General Specifications64
Table 3-5 Series 48 General Specifications64
Model 48-1 Package Outline Drawing66
Figure 3-10 Model 48-1 Package Outline and Mounting Dimensions66
Model 48-2 Package Outline Drawing67
Figure 3-11 Model 48-2 Package Outline and Mounting Dimensions67
Model 48-5 Package Outline Drawing68
Figure 3-12 Model 48-5 Package Outline and Mounting Dimensions68
Maintenance/Troubleshooting69
Maintenance69
Disabling the Laser70
Daily Inspections70
Storage/Shipping70
Cleaning Optical Components71
Troubleshooting72
Introduction73
J48 Interconnect Schematic74
Figure 4-1 Model J48 Series Interconnect Schematic74
J48 Control Board Schematic75
Figure 4-2 J Series Control Board Schematic75
Resetting Faults76
Laser Faults77
Table 4-2 Series 48 Cooling Specifications78
Beam Delivery Optics79
Closed Loop Stabilization Kit82
Introduction82
Safety Precautions82
Connecting83
Figure A-1 Typical Closed Loop Setup83
Operation84
Closed Loop Specifications84

Related product manuals

Synrad Firestar V Series

109 pages

Synrad Firestar Series

96 pages

Synrad Firestar v40

109 pages

Synrad Firestar f series

140 pages

Synrad Firestar f201

140 pages

Synrad 48 Series - Operation

Table of Contents

Related product manuals