TechnipFMC Smith Meter - Page 21

51 pages

To Next Page

To Previous Page

Network Meter Block Installation, Operation, & Maintenance Manual

Installation 16

Figure 10: Meter Pulse Inputs from a PRIME 4 PD Meter Pulser

Figure 11: Meter Pulse Inputs from a Genesis PD Meter’s

HRE Board (Configured with an RTD)

Main Page

Table of Contents3
Introduction6
Product Description6
NMB Models6
Included Equipment7
Integral Equipment7
Ancillary Equipment7
Receipt of Equipment7
Storage Instructions7
Warnings and Precautions8
Configuration8
Hazardous Locations8
Precautions in Hazardous Locations8
Electrostatic Discharge Precautions9
RF Radiation9
Weights & Measures Requirements9
Pre-Installation Considerations10
Electrical Installation Considerations10
Power Supply10
Division 2/Zone 2 Hazardous Area Considerations11
External Fuse Protection11
Typical Wire Sizes11
Real-Time Clock Synchronization12
Installation13
Physical Installation13
Installing a Panel-Mounted NMB13
Installing the NMB with an Instrument Housing14
Installing the NMB or NMT on a Turbine Meter15
Pulse Transmission15
Connecting to a PRIME 4 or Genesis PD Meter16
PRIME 4 Meter16
Genesis Meter16
Electrical Installation17
Evaluation Standards Used17
North American Installations17
ATEX and Iecex Zone 1 Installations17
ATEX and Iecex Zone 2 Installations18
Typical Wiring Diagrams19
Finishing and Testing the Installation22
Power Supply22
Network Connection23
Monitoring and Configuring the NMB24
Remotely Accessing the NMB24
Accessing the NMB Using a Web Browser24
Setting an Initial IP Address24
Launching the NMB Dashboard25
Communicating with a PLC or SCADA System25
Digital Outputs25
Digital Inputs26
Communicating with an MQTT-Protocol Interface26
Implementing Security26
Configuring Your NMB27
Accessing the Configuration Area27
Navigating the Configuration Area28
Configuring Inputs and Outputs28
Viewing I/O Statuses28
Calibrating Analog Inputs29
Configuring Basic Inputs and Outputs30
Configuring Meter Settings32
Viewing Meter Flow Rates & Alarms32
Configuring General Meter Parameters32
Meter Linearization34
Configuring Turbine Meter Options34
Viewing the Turbine Meter Status34
Enabling Turbine Meter Diagnostics35
Re-Characterizing a Turbine Meter's Signature36
Viewing System Status Details36
Viewing OLED Display Panel Information36
Adding Custom Messages to the OLED Display Panel36
Viewing Recent Alarms37
Viewing Server Connections37
Viewing Hardware Information37
Viewing Firmware Information37
Configuring Network Settings37
Changing Your Nmb's IP Address37
Configuring NPT Server Settings38
Configuring MQTT Server Settings38
Adding an Instrument Tag39
Restoring Factory-Default Configuration Parameters39
Rebooting the NMB39
Backing up Your Configuration Settings40
Restoring Your Configuration from a Backup40
Using the Bootloader40
Launching the Bootloader40
Changing Your Nmb's Login Credentials41
Viewing Security Certificates42
Updating Your Nmb's Firmware42
Re-Launching the NMB Firmware and Exiting the Bootloader43
Monitoring and Resetting Alarms43
Alarm Generation43
Alarm Types43
Alarm Severity44
Resetting Alarms in the Nmb's Web Interface44
Resetting All Latched Alarms at Once45
Resetting Alarms45
Resetting Alarms Via MQTT45
Resetting Alarms Via Digital Input45
Maintenance46
Replacing the Clock Battery46
Troubleshooting48
Appendix A: Data Reference for Restful and MQTT Schemas49
Schemas Defining Content of JSON/XML Data Structures49
JSON-Formatted Data Structures49
XML-Formatted Data Structures50

TechnipFMC Smith Meter - Page 21

Table of Contents

Other manuals for TechnipFMC Smith Meter

Related product manuals