Topcon ES-52 - Page 28

To Next Page

To Previous Page

5. BASIC OPERATION

*7 Laser-pointer display

Switching Laser-pointer ON/OFF: "5.1 Basic Key Operation"

:Laser-pointer is ON

*8 Appears when laser beam is emitted for distance measurement

*9 Input mode

:Inputting capital letters and figures.

:Inputting small letters and figures.

:Inputting numbers.

Main Page

Table of Contents5
Precautions for Safe Operation9
Precautions13
Laser Safety Information17
Functions19
Parts of the Instrument19
Mode Diagram22
Basic Operation23
Basic Key Operation23
Display Functions26
Star Key Mode29
Using the Battery30
Battery Charging30
Installing/Removing the Battery32
Setting up the Instrument33
Centering33
Levelling34
Focussing and Target Sighting37
Power On/Off39
Angle Measurement41
Measuring the Horizontal Angle between Two Points41
(Horizontal Angle 0°)41
Setting the Horizontal Angle to a Required Value42
(Horizontal Angle Hold)42
Angle Measurement and Outputting the Data44
Distance Measurement45
Returned Signal Checking46
Distance and Angle Measurement47
Recalling the Measured Data48
Distance Measurement and Outputting the Data49
Coordinate Measurement and Outputting the Data50
REM Measurement52
Setting Instrument Station55
Entering Instrument Station Data and Azimuth Angle56
Setting Instrument Station Coordinate with Resection Measurement63
Coordinate Measurement76
Setting-Out Measurement79
Coordinates Setting-Out Measurement80
Distance Setting-Out Measurement83
REM Setting-Out Measurement86
Setting-Out Line88
Defining Baseline88
Setting-Out Line Point93
Setting-Out Line Line96
Setting-Out Arc99
Defining an Arc99
Setting-Out Arc106
Point Projection110
Defining Baseline110
Point Projection111
Topography Observation113
Observation Setting114
Observation117
Offset Measurement121
Single-Distance Offset Measurement121
Angle Offset Measurement123
Two-Distance Offset Measurement125
Plane Offset Measurement128
Column Offset Measurement130
Missing Line Measurement132
Measuring the Distance between 2 or more Points132
Changing the Starting Point137
Surface Area Calculation139
Intersections143
Traverse Adjustment147
Route Surveying156
Instrument Station Settings156
Straight Line Calculation157
Circular Curve Calculation159
Spiral Curve162
Parabola168
Point Calculation172
Intersection Angle/Azimuth Angle Calculation175
Route Calculation177
Cross Section Survey192
Point to Line MEASUREMENT198
Recording Data - Topo Menu201
Recording Instrument Station Data201
Recording Backsight Point203
Recording Angle Measurement Data206
Recording Distance Measurement Data207
Recording Coordinate Data208
Recording Distance and Coordinate Data210
Recording Notes211
Reviewing JOB Data212
Deleting Recorded JOB Data214
Selecting/Deleting a Job216
Selecting a JOB216
Deleting a JOB219
Registering/Deleting Data220
Registering/Deleting Known Point Data220
Reviewing Known Point Data224
Registering/Deleting Codes225
Reviewing Codes227
Outputting Job Data228
Outputting JOB Data to Host Computer228
Changing the Settings232
Configuration -Config Mode232
EDM Settings239
Allocating Key Functions243
Changing Password247
Restoring Default Settings248
Warning and Error Messages249
Checks and Adjustments254
Circular Level254
Tilt Sensor255
Collimation258
Reticle259
Optical Plummet262
Additive Distance Constant264
Standard Equipment and Optional Accessories266
Standard Equipment266
Optional Accessories266
Prism System268
Power Supplies269
Specifications270
Explanation275
Manually Indexing the Vertical Circle by Face275
Face 2 Measurement275
Correction for Refraction and Earth Curvature277
Regulations278

Topcon ES-52 - Page 28

Table of Contents

Related product manuals