EasyManua.ls Logo

Toro GrandStand 71504 - User Manual

Toro GrandStand 71504
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Form No. 3466-593 Rev A
GrandStand
®
Mower
W ith 48in, 52in, or 60in TURBO FORCE
®
Cutting Unit
Model No. 71504 —Serial No. 415338000 and Up
Model No. 71505 —Serial No. 412999999 and Up
Model No. 72504 —Serial No. 415324575 and Up
Model No. 72505 —Serial No. 415338000 and Up
Model No. 72507 —Serial No. 416360000 and Up
Model No. 72509 —Serial No. 415247000 and Up
Model No. 72512 —Serial No. 416360000 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3466-593*

Table of Contents

Questions and Answers

  • C
    Cameron HuberAug 12, 2025
    Why won't my Toro Lawn Mower engine start?
    • D
      daniellerandallAug 12, 2025
      There are several reasons why your Toro Lawn Mower engine might not start. It could be due to an empty fuel tank or a closed shutoff valve, so fill the tank and open the valve. A loose or disconnected spark-plug wire can also be the culprit; in this case, install the wire on the spark plug. Other potential causes include a pitted, fouled, or incorrectly gapped spark plug (install a new one), a dirty air cleaner (service the air-cleaner element), or dirt in the fuel filter (replace the fuel filter). For issues related to dirt, water, or stale fuel in the fuel system, or an incorrect gap between the safety-interlock switches, it's best to contact an Authorized Service Dealer.
  • M
    Mrs. Laura CunninghamAug 15, 2025
    Why is my Toro GrandStand 71504 Lawn Mower engine losing power?
    • A
      Amanda LeonardAug 16, 2025
      Your Toro Lawn Mower engine may be losing power due to several reasons. The engine load could be excessive, so try reducing the ground speed. A dirty air cleaner can also cause this issue, so service the air-cleaner element. Check the oil level in the crankcase and add oil if it's low. Make sure the cooling fins and air passages under the engine blower housing are free of obstructions. A spark plug that is pitted, fouled, or has an incorrect gap should be replaced. Also, check the fuel cap vent hole and clean or replace the cap if it's plugged. Finally, replace the fuel filter if it's dirty. For dirt, water, or stale fuel in the fuel system, contact an Authorized Service Dealer.
  • B
    Benjamin EnglishAug 23, 2025
    How to fix uneven cutting height on my Toro Lawn Mower?
    • J
      julie08Aug 23, 2025
      Uneven cutting height on your Toro Lawn Mower can be due to several reasons. Start by sharpening the blades if they are not sharp. If the cutting blades are bent, install new ones. Ensure the mower deck is level by adjusting the side-to-side position and adjusting the front-to-rear pitch. Clean the underside of the mower deck if it's dirty. Adjust the tire pressure to the correct level. For a bent blade spindle, contact an Authorized Service Dealer.
  • P
    Paul FitzgeraldAug 27, 2025
    What to do if my Toro GrandStand 71504 engine overheats?
    • C
      Christopher WalkerAug 27, 2025
      If your Toro Lawn Mower engine overheats, it could be due to a few reasons. First, the engine load might be excessive, so reduce the ground speed. Also, check the oil level in the crankcase and add oil if it's low. Another potential cause is blocked cooling fins and air passages under the engine blower housing; remove any obstructions from these areas.
  • J
    jesse95Aug 31, 2025
    What to do if the blades on my Toro GrandStand 71504 Lawn Mower do not rotate?
    • S
      Susan MayAug 31, 2025
      If the blades on your Toro Lawn Mower aren't rotating, start by checking the belt tension if the pump-drive belt is worn, loose, or broken. If the pump-drive belt is off the pulley, install the drive belt and check the adjusting shafts and belt guides for the correct position. If the mower-deck belt is worn, loose, or broken, install a new deck belt. If it's off the pulley, install the deck pulley and check the idler pulley, idler arm, and spring for correct position and function. Replace any broken or missing idler springs. Also, adjust the clutch air gap if the electric clutch is out of adjustment. For issues with the clutch connector or wire, a damaged electric clutch, the safety-interlock system, or a faulty PTO switch, contact an Authorized Service Dealer.
  • M
    Monica LopezSep 3, 2025
    How to fix abnormal vibration in my Toro GrandStand 71504?
    • W
      wbarajasSep 3, 2025
      Abnormal vibration in your Toro Lawn Mower can be caused by several factors. Bent or unbalanced cutting blades are a common cause, so install new cutting blades. Check if any blade-mounting bolts or engine-mounting bolts are loose and tighten them. Also, inspect the engine pulley, idler pulley, or blade pulley for looseness and tighten the appropriate pulley. For a damaged engine pulley or a bent blade spindle, contact an Authorized Service Dealer.
  • C
    Chelsea JohnsonSep 7, 2025
    What to do if the clutch does not engage on my Toro GrandStand 71504 Lawn Mower?
    • G
      goodwindanielSep 8, 2025
      If the clutch on your Toro Lawn Mower doesn't engage, start by replacing the fuse if it's blown and check the coil resistance, battery charge, charging system, and wiring connections, replacing components if necessary. Check for low voltage supply at the clutch, examining coil resistance, battery charge, charging system, and wiring, and replace parts as needed. If the coil is damaged, replace the clutch. For inadequate current supply, repair or replace the clutch lead wire or electrical system, and clean the connector contacts. If the rotor/armature air gap is too large, remove the shim or replace the clutch.
  • B
    Betty WilliamsSep 10, 2025
    Why my Toro GrandStand 71504 Lawn Mower doesn't drive?
    • F
      frycurtisSep 12, 2025
      If your Toro Lawn Mower isn't driving, the hydraulic-fluid reservoir might be low, so add hydraulic fluid. Air in the hydraulic system can also be a cause, so bleed the air out. Check if the pump-drive belt slips and replace it if necessary. If a pump-drive belt idler spring is missing, replace it. Lastly, ensure the pump-bypass valves are tightened to a torque of 12 to 15 N?m (9 to 11 ft-lb).

Toro GrandStand 71504 Specifications

General IconGeneral
BrandToro
ModelGrandStand 71504
CategoryLawn Mower
LanguageEnglish

Related product manuals