A ÷ L
ProgrammingchanneJsintothe TV'schanneJmemory
When }_oupress CHANNEL A or V on the remote contrd or
TV front pand, your TV will stop only on d_echarmds stored
in the TV's channd memor>
Follow the steps bdow to program chamMs into the TV's
chamM memor>
ProgrammingchanneUsautomat[caRy
Your TV can automatically dececEall active charmds in your
area and store them in its mernor> After the chaimds are
programmed amomaticall> you can manually add or erase
individual churnMs.
Note:
* X_ulnustcor/@,umtl_ear_enrmislputsourcesbefore
proclmmmirTg charffTeL_ (see page 40)
* 777eautomaticchanne/pmgr_mminrlpmeessdoesNOTelase
dTannels that were pl evk_us/yprogr_lmmed /nto the 7-1/_
rylefi7or_/but adds newly found dTanne£ to _<heex£tilw set of
programmed channels _ r_move a ehannd from the memory
yOU fTIUStrTlanuil/Ijl delete/t _uee fText paule_
* 7_JtunetheTVtoachanndnotpmgfammedkTthed_annd
rTler77Ol% VOU fFitJst use the CJiTalllld Nui77/?er btJ_OllS o/7 the
f_lY}OtP_ COIItlDL
" P/ogl_wTmbg dTannels br an arTtelT/_abput corTfll_'Uled br
CABLE win tiske sLbst_sntia/lybnger than for aft antenna ifTput
confl:qumd for ANTENIVA This i;_noiTnM howevel; once
d}annd pFo_r_,fTTFR/Rg IScornpleted, jlOU shou/cJnot have to
r_/:)eatthepfogl>7lTIm/£g processagainunles'_your Cabb TV
sen/ice lineup chaeulessiqn/ficlmtly
* If you have a &J?/eCARD inserted (page 12), channel
progmmmifW for ANT 7£ dlsabled becnuse tile C'rsb/eC_ARD
automatie_ffly loads _tse(2shimd}annd /£t in the TV_ d?annd
memosy
To program channels automatically:
1. Make sure you have configured the antenna input sources.
See page 41 for details.
2. Press MENU and open the SETUP menu.
3. HigNighc INSTALLATION and press ENTER. (A new se_
of INSTALLATION menu icons will appear on-screen.
_ Select_#_Navtgate _Back _s!_ _xit
4. Open the TERRESTRIAL mem*, highlight CHANNEL
PROGRAM, and press ENTER.
5. Highlight ANT 1 or ANT 2, depending on which antenna
inpur you want to program channds fi._r,and then press
ENTER to start amomauc chamM programming.
_ Navigate {_Select _l_Back ),_£xit
i@ ANT I Antenna
Scanni{/g cham/els please war
The TV will amomafically cycle d_rough all d_e channds
f}._rthe ame*ma input you sdecced, and score all acuve
channds in the channd memor> Whib _heTV is Waling
through the channds, the message "Scanning chamMs,
please wait" appears (as shown above righ0.
To cancd channd programming, eid_er press EXIT or
highlight ABORT in d_eon-screen disphy and press
ENTER.
When chamM programming is done, press
CHANNEL _ or _ to xiew d_e programmed &amMs.
Channel
Numbers
CHANNEL _
TVfrontpanel
,_,'_7--v_ --_m_ t _×,T_,_,0_od,;_,_i,
CHANNEL_'/ ±
÷
H94(E)O40-43(6a-Setup)
Copyright @ 2004 TOSHIBA CORPORATION, All rights reserved,
÷
813/04, 5:22 PM
41
r
To Next Page
Loading...
