Toshiba B-EX4 - Page 4

EO18-33027
5.5 Fine adjustment value setting/ ADJUST SET ------------------------------------------------------------5-37
5.5.1 Feed / FEED ADJ.----------------------------------------------------------------------------------------- 5-38
5.5.2 Cut position / CUT ADJ ---------------------------------------------------------------------------------- 5-38
5.5.3 Back feed / BACK ADJ----------------------------------------------------------------------------------- 5-43
5.5.4 X direction position / X ADJUST----------------------------------------------------------------------- 5-44
5.5.5 Density fine tune (Thermal transfer) / TONE ADJ.(TRANS.) ---------------------------------- 5-44
5.5.6 Density fine tune (Direct thermal transfer) / TONE ADJ.(DIRECT) --------------------------- 5-44
5.5.7 Ribbon (Rewinder) / RBN ADJ.<FW>---------------------------------------------------------------- 5-45
5.5.8 Ribbon (Feeder) / RBN ADJ.<BK>-------------------------------------------------------------------- 5-45
5.5.9 Refrective sensor fine tune / THRESHOLD <REFL.> ------------------------------------------- 5-46
5.5.10 Transmissive sensor fine tune / THRESHOLD <TRANS.> ------------------------------------- 5-46
5.6 TEST PRINT------------------------------------------------------------------------------------------------------5-48
5.6.1 Print condition setting / PRINT CONDITION-------------------------------------------------------- 5-48
5.6.2 1-dot slant line print / SLANT LINE(1DOT) --------------------------------------------------------- 5-51
5.6.3 3-dot slant line print / SLANT LINE(3DOT) --------------------------------------------------------- 5-51
5.6.4 Character print / CHARACTERS ---------------------------------------------------------------------- 5-52
5.6.5 Barcode print / BARCODE ------------------------------------------------------------------------------ 5-52
5.6.6 White line print / NON-PRINTING--------------------------------------------------------------------- 5-53
5.6.7 Factory test / FACTORY TEST ------------------------------------------------------------------------ 5-53
5.6.8 Auto print (Transmissive) / AUTO PRINT (TRANS.) --------------------------------------------- 5-53
5.6.9 Auto print (Reflective) / AUTO PRINT (REFL.) ---------------------------------------------------- 5-54
5.7 SENSOR ADJUSTMENT--------------------------------------------------------------------------------------5-55
5.7.1 Temperature sensor/ TEMPERATURE-------------------------------------------------------------- 5-55
5.7.2 Reflective sensor / REFLECT -------------------------------------------------------------------------- 5-55
5.7.3 Transmissive / TRANS. --------------------------------------------------------------------------------- 5-56
5.7.4 Paper empty level / PE REFL./TRANS. ------------------------------------------------------------- 5-56
5.7.5 Ribbon end / RIBBON------------------------------------------------------------------------------------ 5-56
5.8 RAM CLEAR------------------------------------------------------------------------------------------------------5-57
5.8.1 No RAM clear / NO RAM CLEAR -------------------------------------------------------------------5-57
5.8.2 Counter clear / MAINTE.CNT CLEAR
--------------------------------------------------------------5-57
5.8.3 Parameter clear / PARAMETER CLEAR
----------------------------------------------------------5-58
5.9 IP ADDRESS SETTING ---------------------------------------------------------------------------------------5-64
5.9.1 Network / NETWORK ------------------------------------------------------------------------------------ 5-64
5.9.2 USB----------------------------------------------------------------------------------------------------------- 5-69
5.9.3 RS-232C----------------------------------------------------------------------------------------------------- 5-70
5.9.4 Centronics / CENTRO. ---------------------------------------------------------------------------------- 5-71
5.10 BASIC SETTING-------------------------------------------------------------------------------------------------5-72
5.10.1 Basic function / BASIC ----------------------------------------------------------------------------------- 5-72
5.10.2 File display / FILE MAINTENANCE------------------------------------------------------------------- 5-72
5.10.3 Trace function / TRACE---------------------------------------------------------------------------------- 5-72
5.10.4 Extended mode / EXPAND MODE-------------------------------------------------------------------- 5-72
5.11 RFID Module Setting--------------------------------------------------------------------------------------------5-73
5.11.1 Test / TEST ------------------------------------------------------------------------------------------------- 5-74
5.11.2 Module / MODULE---------------------------------------------------------------------------------------- 5-75
5.11.3 Retry / RETRY --------------------------------------------------------------------------------------------- 5-77
5.11.4 UHF setting / UHF SETTING--------------------------------------------------------------------------- 5-79
5.11.5 Other / OTHER--------------------------------------------------------------------------------------------- 5-83