Toshiba E-STUDIO 2500C User Manual (English)

Other manuals for Toshiba E-STUDIO 2500C

Operator's Manual418 pages

Manual232 pages

Quick Start Guide90 pages

Scanning Guide146 pages

Questions and Answers:

C
Carlos PrinceAug 19, 2025
What to do if Toshiba All in One Printer display does not change when buttons are pressed?
- D
  Doris CarterAug 19, 2025
  If the Toshiba All in One Printer display doesn't change when buttons are pressed, it might be in energy-saving mode. Press the [ENERGY SAVER / SHUTDOWN] or [START] button to exit this mode. Note that it may take a moment for the equipment to become ready. Alternatively, if the power is off due to the weekly timer, press the [START] button to turn the power back on. If using department management, ensure the correct code is entered. For user management, verify the user information is accurate. Finally, if the 'Warming up' message is displayed, wait for the equipment to finish warming up.
M
Michael DanielsAug 21, 2025
Why does paper jamming occur frequently in my Toshiba All in One Printer?
- S
  solisarianaAug 21, 2025
  Frequent paper jams in your Toshiba All in One Printer could be due to several reasons. First, check if the paper size setting on the control panel matches the paper in the drawer or bypass tray. If the paper exceeds the indicated line inside the side guide, remove some sheets. Ensure there's an appropriate space between the side guide and the paper, placing the paper straight along the side guide. If the cause is not listed above, follow the guidance shown on the touch panel to locate and remove the jammed paper.
J
Joyce McgrathAug 23, 2025
How to fix image trouble on Toshiba E-STUDIO 2500C?
- M
  Matthew BryantAug 23, 2025
  To address image trouble on your Toshiba All in One Printer, ensure the Automatic Document Feeder or Platen Cover is fully lowered to block outside light. Clean the original glass, platen sheet, scanning area, and guides if dirty. If the copy density is too dark, lighten it in manual mode or switch to automatic copy density mode. For highly transparent originals, place a blank sheet of paper over the original. Make sure there is contact between the original and the glass. Verify that the size and direction of the copy paper and the original, or the reproduction ratio, are set correctly. Also, clean the scanning area, guides, main charger, and slit glass.
C
carmenbradshawAug 26, 2025
What to do if Toshiba E-STUDIO 2500C image density is too low?
- P
  Paula ChangAug 27, 2025
  If the image density is too low on your Toshiba All in One Printer, first check if the touch panel displays a message to replace the toner cartridge and replace it if needed. If not, adjust the image density using the manual density buttons or the background adjustment function.
B
bethanypayneAug 28, 2025
What to do if Toshiba All in One Printer image density is too high?
- A
  allenmichaelAug 28, 2025
  If the image density is too high on your Toshiba All in One Printer, adjust the image density using the manual density buttons or the background adjustment function.
E
Edward BenitezAug 30, 2025
Why Toshiba E-STUDIO 2500C All in One Printer functions cannot be set?
- D
  Dominique MartinezAug 30, 2025
  If functions cannot be set on your Toshiba All in One Printer, it may be due to incompatible function combinations. Refer to the copying function combination and image quality adjustment combination matrices, and then set them again.
D
Daniel LawsonSep 2, 2025
How to fix Toshiba E-STUDIO 2500C All in One Printer that does not start?
- R
  rgreenSep 2, 2025
  If your Toshiba All in One Printer does not start, ensure the power cord is fully inserted into the plug until it stops. Also, make sure the cover is properly closed.
R
Roger SullivanSep 4, 2025
Why does my Toshiba All in One Printer keep jamming?
- T
  Timothy NelsonSep 4, 2025
  Frequent paper jams in your Toshiba All in One Printer can occur for several reasons: * If the message “Check paper size setting on control panel for drawer N (Bypass)” appears, match the paper size in the drawer or bypass tray to the equipment's setting. * If the paper exceeds the line inside the side guide, remove some sheets so the paper height doesn't exceed the line. * Ensure an appropriate space between the side guide and paper, placing the paper straight along the side guide. * If you can't easily find the jammed paper, follow the guidance shown on the touch panel.

Toshiba E-STUDIO 2500C Specifications

General

Functions	Print, Copy, Scan, Fax
Print Technology	Laser
Print Speed (Color)	25 ppm
Print Speed (Black)	25 ppm
Print Resolution	600 x 600 dpi
First Print Out Time (Mono)	8.4 seconds
Scan Resolution	600 dpi
Copy Speed	25 cpm
Copy Resolution	600 x 600 dpi
Fax Transmission Speed	33.6 kbps
Fax Resolution (Super Fine)	300 x 300 dpi
Supported Operating Systems	Windows, Mac OS
Paper Size	A3, A5, B5, Legal, Letter, Executive
Scanner Type	Color Scanner
Interface	USB 2.0, Ethernet