Trane IntelliPak User Manual

Warnings, Cautions and Notices
4 RT-SVX36K-EN
• If the job site inspection of the unit reveals damage or
material shortages, file a claim with the carrier
immediately. Specify the type and extent of the
damage on the “bill of lading” before signing.
• Visually inspect the internal components for shipping
damage as soon as possible after deli very and before
it is stored. Do not walk on the sheet metal base pans.
• If concealed damage is discovered, notify the carrier's
terminal of damage immediately by phone and by
mail. Concealed damage must be reported within 15
days.
• Request an immediate joint inspection of the damage
by the carrier and the consignee. Do not remove
damaged material from the receiving location.Take
photos of the damage, if possible.The owner must
provide reasonable evidence that the damage did not
occur after delivery.
• Remove the protective plastic coverings that shipped
over the compressors.
Storage
Take precautions to prevent condensate from forming
inside the unit’s electrical compartments and motors if:
a. the unit is stored before it is installed; or,
b. the unit is set on the roof curb, and temporary heat
is provided in the building. Isolate all side panel
service entrances and base pan openings (e.g.,
conduit holes, S/A and R/A openings, and flue
openings) from the ambient air until the unit is
ready for startup.
Note: Do not use the unit's heater for temporary heat
without first completing the startup procedure
detailed under “Starting the Unit”.
Trane will not assume any responsibility for equipment
damage resulting from condensate accumulation on the
unit's electrical and/or mechanical components.
Factory Warranty Information
Compliance with the following is required to preserve the
factory warranty:
All Unit Installations
Startup MUST be performed byTrane, or an authorized
agent ofTrane, to VALIDATE this WARRANTY. Contractor
must provide a two-week startup notification toTrane (or
an agent ofTrane specifically authorized to perform
startup).
On all IntelliPak I units, aTrane factory REQUIRED startup
(mandatory with Evaporative Condensing or optionally
selected ON OTHER UNITS) provides "maximized unit
reliability and overall unit performance," in addition to
preserving the standard factory warranty.
Additional Requirements for Units Requiring
Disassembly
When a new fully assembled IntelliPak is shipped and
received from ourTrane manufacturing location, and, for
any reason, it requires disassembly or partial
disassembly-which could include but is not limited to the
evaporator, condenser, control panel, compressor/motor,
factory mounted starter or any other components
originally attached to the fully assembled unit-compliance
with the following is required to preserve the factory
warranty:
• Trane, or an agent ofTrane specifically authorized to
perform start-up and warranty ofTrane® products, will
perform or have direct on-site technical supervision of
the disassembly and reassembly work.
• The installing contractor must notifyTrane-or an agent
ofTrane specifically authorized to perform start-up and
warranty ofTrane® products-two weeks in advance of
the scheduled disassembly work to coordinate the
disassembly and reassembly work.
• Start-up must be performed byTrane or an agent of
Trane specifically authorized to perform start-up and
warranty ofTrane® products.
Trane, or an agent ofTrane specifically authorized to
perform startup and warranty of Trane® products, will
provide qualified personnel and standard hand tools to
perform the disassembly work at a location specified by
the contractor.The contractor shall provide the rigging
equipment such as chain falls, gantries, cranes, forklifts,
etc. necessary for the disassembly and reassembly work
and the required qualified personnel to operate the
necessary rigging equipment.
WARNING
No Step Surface!
Do not walk on the sheet metal drain pan. Walking on
the drain pan could cause the supporting metal to
collapse, resulting in the operator/technician to fall.
Failure to follow this recommendation could result in
death or serious injury.

Trane IntelliPak Specifications

General

Brand	Trane
Model	IntelliPak
Category	Air Conditioner
Language	English