Tryax TY30-VS User Manual (English)

Questions and Answers:

F
Frank RomanAug 3, 2025
What to do if X and Z axis won't move on my Tryax TY30-VS Lathe?
- A
  antonio14Aug 3, 2025
  If the X and Z axes of your Tryax Lathe won't move, several issues could be at play. First, check if a fuse has blown and replace it if necessary. Also, verify if the AL has tripped. If it has, record the fault signal and contact the appropriate service entity to address it. Ensure that the axes are not touching the limit. Inspect for any broken wires and examine related systems or parts for faults. Other potential causes include a stuck bearing (replace if stuck), screw faults (replace if faulty), a heated motor (check motor load, wire connectors, and overload protection relay, and clean the motor's external surface), or a motor that simply won't run (replace the motor if this is the case).
T
Tina MartinezAug 9, 2025
Why is the X-axis shaking on my Tryax TY30-VS Lathe?
- M
  Michael SchultzAug 9, 2025
  If the X-axis on your Tryax Lathe is shaking, there could be several reasons. Start by checking the oil level and renew or supplement the oil if it's low. Ensure you're using the correct oil, specifically SHELL R68 guide-way oil. If there's noise, the oil flow rate may be the problem and the part needs to be replaced. Also, check if the level error is too big and re-adjust the level if needed. Finally, if there is noise during operation, the track lubrication may be abnormal, so check the lubrication system.
G
grobinsonAug 14, 2025
What to do if X-axis and Z-axis are not lubricated on my Tryax TY30-VS Lathe?
- C
  Christian WarrenAug 15, 2025
  If the X and Z axes of your Tryax Lathe are not being lubricated, begin by checking if a fuse is burnt and replace it if necessary. Also, see if the thermo-timer trips, and investigate the reason that causes the trip. If a wire is broken, contact the service personnel to handle it. If the electric lubricator is faulty, it should be replaced. Finally, the filter or oil-hole outlet might be stuck; in that case, shutdown the system and clean the filter and oil-hole.

Tryax TY30-VS Specifications

General

Brand	Tryax
Model	TY30-VS
Category	Lathe
Language	English

Summary

Safety Notes

Safety Specification

Details safety devices and operator training requirements for safe machine operation.

General Safety Notes

Lists general safety precautions for machine operation, maintenance, and work area.

Notes after Machining Operation Stops

Advises on safe procedures after stopping machining operations, including waiting for chuck to stop.

Notes on Handling Abnormal Status

Instructions for immediate actions during abnormal status, including emergency stop and power off.

Maintenance Safety Notes

Safety precautions before, during, and after maintenance, including power lockout and cleanliness.

Routine Maintenance

Outlines routine maintenance tasks like keeping the bed clean and checking gauges.

Noise

Specifies noise level standards and measurement positions for machine operation.

Machine Brief Introduction

Mechanical Specification

Provides detailed technical specifications of the TY30-VS machine, including dimensions and components.

Machinery Outline Scheme Diagram

Presents overall dimensions and layout of the machine with an isometric view.

Assembly Drawing & Machine list

Shows an exploded view of the machine and lists major assembly components.

Foundation Plan

Details the required foundation dimensions and anchor bolt locations for machine installation.

Mechanical Coordinate System

Defines the X and Z axes directions for tool post movement.

Jaw Chuck size

Provides dimensions and specifications for the jaw chuck.

Tool Holder Dimension Drawing

Illustrates the dimensions of tool holders for left and right cutters.

Move, Store and Install the Machine

Pre-installation Preparation Works

Lists requirements for power, pneumatics, oils, and measuring equipment before installation.

Unload and Moving the Machine

Details the process of unloading the machine package using a forklift.

Installation and Levelling

Explains the process of installing and leveling the machine using a level meter.

Machine leveling adjustment

Guides the user on accurately leveling the machine axes using a level meter.

Installing the Peripherals

Provides step-by-step instructions for connecting air, lubrication, and electrical systems.

Power Requirement

Specifies the electrical power input, grounding requirements, and safety notes.

Compressed Air Source

Details requirements for the compressed air supply, including pressure, flow rate, and filtering.

Other Objects

Lists recommended cleaning utensils such as kerosene, rags, and brushes.

Pre-boot Preparation Works

Pre-boot Check

Lists essential checks before booting the machine for safety and proper operation.

Oil-feed and Oil Types

Explains the auto oil-feeding system and lists recommended oils for lubrication.

Machine's Oil-feed Points

Illustrates the specific points on the machine where oil should be fed.

Referenced Machine Oils

Provides a list of recommended machine oils with specifications and capacities.

Chips Removal

Instructs on manually cleaning and sweeping chips to the chip tank.

Machine Maintenance and Tuning

Maintenance Period

Discusses the importance of regular maintenance for machine longevity and efficiency.

Maintenance Interpretation

Explains the purpose and methods of maintenance for extending machine life.

Machine Regular Maintenance Frequency List

Presents a frequency list for daily, weekly, monthly, and yearly maintenance tasks.

Maintenance Check Sheet

Provides daily and weekly maintenance check sheets with items and confirmation status.

Soft jaw chuck Mechanism

Details the gripping capacity of the soft jaw chuck for different diameters.

Forced Auto Lubricator

Explains the specifications and graphical demonstration of the forced auto lubricator.

Troubleshooting of lubrication unit

Lists common faults in the lubrication unit, their reasons, and troubleshooting methods.

Troubleshooting

Machine Troubleshooting

Provides a table for troubleshooting common machine issues like axis shaking and movement failure.

Quick-Wear Part List

Lists quick-wear parts with their specifications, materials, and quantities.

Machine Parts List

Machine Parts List Diagram

Illustrates the machine components with corresponding numbers for identification.

Machine Parts List (Base Unit)

Lists parts for the base unit of the machine, including drawing numbers and specifications.

Machine Parts List (Column Unit)

Details parts related to the column unit, including switches and bearings.

Machine Parts List (Head Unit)

Presents the list of parts for the head unit, including slides and cutters.

Tryax TY30-VS User Manual

Table of Contents