Videx GSM4K/4G - Programming the GSM Intercom; PROGRAMMING THE GSM INTERCOM; PROGRAMMING BY TEXT MESSAGE; 4 DIGIT CODE

66250754-4G-EN - V2.0 - 28/03/22
- 37 -
4000 Series GSM Audio Intercom - Technical Manual
4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
PROGRAMMING THE GSM INTERCOM
Programming the 4G GSM intercom can be carried out by one of the following methods: sending text (SMS) messages, by using the
GSMSK PC software (ver 4.1.0.35 or later), also refer to the programming manual GSMSK_66251720-EN_V2-1 (or later) or by using
the GSM mobile apps: Videx SMS Wizard (for administrators) and the Videx SMS Wizard PRO (for installers and engineers) also see
additional notes on page 67.
IMPORTANT NOTE: When you are required to use “ in a text message it is important to use the correct symbol and not for example
‘ or two ‘ single apostrophes side by side which may look the same, but will be interpreted dierently by the GSM intercom.
PROGRAMMING BY TEXT MESSAGE
Programming by text message is a simple way to customise the settings of the GSM intercom and add or delete telephone numbers.
If you have several buttons or telephone numbers to enter you may nd programming easier with the GSMSK PC software. Simply
send texts in the following format shown below to the telephone number of the SIM within the GSM intercom panel:
< 4 DIGIT CODE > < 3 DIGIT FUNCTION CODE > < OPTIONAL DATA > < OPTIONAL ? >
4 DIGIT CODE This code prevents unauthorised access to the programmable features of the system. The code must
be four digits long, but can be any combination using digits 0 – 9. The default code is “1111” and will be
used for all examples in this manual.
3 DIGIT FUNCTION CODE The 3 digit function or command code identies the programmable feature to be changed. The code
must be in capital letters. The following table lists the available codes.
DESCRIPTION CODE EXAMPLE SETTINGS DEFAULT PAGE
Store a primary telephone no. STN 1111STNnnn”01912243174” nnn = 001 - 050 n/a 40 - 42
Store divert 1 telephone no. STD 1111STDnnn”01912241559” nnn = 001 - 050 n/a 40 - 42
Store divert 2 telephone no. STE 1111STEnnn”01912243678” nnn = 001 - 050 n/a 40 - 42
Store divert 3 telephone no. STF 1111STFnnn”01912245326” nnn = 001 - 050 n/a 40 - 42
Store a primary telephone no.
and divert no’s in a single text
message
STN 1111STNnnn”pn”,”d1”,”d2”,”d3”
1111STNnnn”01912243174”,
”01912241559”,” 01912243678”,
”01912245326”
nnn = 001 - 050
pn = primary no.
d1 = divert 1 no.
d2 = divert 2 no.
d3 = divert 3 no.
n/a 40 - 41
Store a dial to open no. (DTO)
or
Store up to 5 dial to open no’s
(DTO) in a single text message to
the next available locations
STR 1111STRnnn”07771234567”
1111STR”n1”,”n2”,”n3”,”n4”,”n5”
1111STR”01912243174”,
”01912241559”,” 01912243678”,
”01912245326”,”07897123456”
nnn = 000 - 999 or
nnn = optional
n1 = 1st DTO
n2 = 2nd DTO
n3 = 3rd DTO
n4 = 4th DTO
n5 = 5th DTO
n/a 41 - 42
Delete a dial to open no. (DTO)
without knowing it’s location
DET 1111DET”01912243174” n/a n/a 42 - 43
Store a temporary dial to open
no. (DTO), store up to 32 temp
no’s max.
TDR 1111TDR”tele”T?
(note: if T is omitted default time
T = 8 hours)
tele = tel no. to
store
T = 1 - 255 hrs
n/a 43
Set call time SPT 1111SPTnn nn = 01 - 12 02 (40s) 43
Set relay time RLT 1111RLTnn nn = 00 - 99 05 (5s) 43
Set auxiliary AO1 output time A1T 1111A1Tnn nn = 00 - 99 05 (5s) 43
Set auxiliary AO1 out mode A1M 1111A1Mnn nn = 00 - 05 01 43 - 44
Set auxiliary AO2 output time A2T 1111A2Tnn nn = 00 - 99 05 (5s) 44
Divert to next no. time DIT 1111DITnn nn = 01 - 99 15 (15s) 44
Check GSM signal strength SIG 1111SIG? n/a n/a 44
Check software version VER 1111VER? n/a n/a 44
Dial a number DLE 1111DLE”123” n/a n/a 44 - 45
Store SMS message for g-4 SMS 1111SMS”HouseAlarm” n/a AUX TRIG 45
Change 4 digit code CDE 1111CDE1234 Any 4 digits 1111 45
Trigger the relay RLY 1111RLY n/a n/a 45
Trigger the auxiliary output AO1 A1O 1111A1O n/a n/a 45
Trigger the auxiliary output AO2 A2O 1111A2O n/a n/a 45