66250754-4G-EN - V2.0 - 28/03/22
- 71 -
4000 Series GSM Audio Intercom - Technical Manual
4000 Series GSM Audio Intercom with Proximity
USER COMMAND TABLES
The following user command table shows the user commands that can be carried out during a call. Successful commands are
signalled by two beeps from the telephone, errors are signalled by four beeps.
IMPORTANT NOTE: When the ED# function has been enabled the user must press the # button on their phone before pressing
any of the following user commands (also refer to page 51 for further information).
FUNCTION 1st KEY TO PRESS 2nd KEY TO PRESS
Latch the relay (unlatch by pressing 3) 10
Release the door or gate 3 n/a
Activate auxiliary output AO1
1
(when A1M = mode 01) 6 n/a
Activate auxiliary output AO2
2
5 n/a
Adjust door speech volume (GSM speaker) 4 0 - 9 (0 = lowest, 9 = highest)
Adjust phone speech volume (GSM mic) 7 0 - 9 (0 = lowest, 9 = highest)
Status Indication for AO1
3
(when A1M = mode 02) 9 n/a
Activating auxiliary output AO1 in this way is only possible when A1M mode has been set to mode 01 (also see notes on pages
43 - 44, set auxiliary output AO1 mode) and will operate for the programmed AO1 time. If the AO1 output time has been set to
latch simply press 6 on the phone to unlatch the output again.
Auxiliary output AO2 will activate for the programmed AO2 time. If the AO2 output time has been set to latch simply press 5 on
the phone to unlatch the output again.
Auxiliary input AO1 status indication is only possible when A1M mode has been set to mode 02 (also see notes on pages 43 - 44,
set auxiliary output AO1 mode).
The next user command table shows the SMS text messages that can be sent to the GSM intercom while in standby (the examples
shown in the table use the default 4 digit master code 1111).
FUNCTION MESSAGE TO SEND
Check the signal strength 1111SIG?
Check network type & connection 1111CON?
Check the available balance
4
1111BAL?
Check the software version 1111VER?
Release the door/gate 1111RLY? (? optional, send if conrmation is required).
Latch the relay 1111RLA? (? optional, send if conrmation is required).
Unlatch the relay 1111RUL? (? optional, send if conrmation is required).
Activate auxiliary output AO1 1111A1O? (? optional, send if conrmation is required).
Latch auxiliary output AO1 1111A1L? (? optional, send if conrmation is required).
Unlatch auxiliary output AO1 1111A1U? (? optional, send if conrmation is required).
Activate auxiliary output AO2 1111A2O? (? optional, send if conrmation is required).
Latch auxiliary output AO2 1111A2L? (? optional, send if conrmation is required).
Unlatch auxiliary output AO2 1111A2U? (? optional, send if conrmation is required).
Check Timeband setting (for call buttons) 1111TBA?
Query Access Control Timeband (0 - 9) 1111ATBn? (where n = timeband 0 - 9, also see notes on pages 47 - 48).
Query Access Level (0 - 9) 1111ACCn? (where n = access level 0 - 9, also see notes on pages 48 - 49) .
Query Free Access Timeband setting (0 - 9) 1111FREn? (where n = free access timeband 0 - 9, also see notes on page 57).
Check Intercom Time and Date 1111CLK?
Check Input Status 1111CHK?
Find a Dial to Open (DTO) number (000 -
999)
1111FDT”yyyyyyyyyyy”? (where yyyyyyyyyyy = telephone number, minimum of
4 digits, also see notes on page 58).
Find a Fob or Card location (000 - 999) 1111FDF”nnnnn”? (where nnnnn = 5 digit user code printed on fob/card, also see
notes on page 53).
Find an Access Code (000 - 399) 1111FDC”code”? (where code = 4 to 8 digit access code, see notes on page 56).
The following command is only applicable when an Art.2813 remote relay is connected via the RS485 bus
Activate remote relay output 1111RLNnna? (where nn = unit ID from 00 - 63 and where a = 1 (trigger relay), 2
(trigger A1 output) or 3 (trigger A3 output), also see notes on page 66.
The balance can only be checked if the correct balance check string has been stored (also see SDL notes on page 45). This feature
is only applicable for pay-as-you-go SIM cards.
User Commands
To Next Page
Loading...
