62
63
Device list and connection
Up to 2 devices can be paired to the
telephone base. All paired devices are
shown on the device list. To use a paired
device, it must be connected. Both
Bluetooth enabled devices can be used
on a cell call at a time.
Once you have paired a device with the
telephone base, you do not need to
repeat the pairing procedure again
unless you delete the device from the
device list.
NOTE
• When connecting a Bluetooth device
to the device list, all connected devices
will be temporarily disconnected until
the procedure is complete. It may take
up to two minutes to reconnect.
Review the device list
1. Press MENU/SELECT on the telephone
base in idle mode to enter the main
menu.
2. Press q CID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press MENU/SELECT again to select
Device list.
Connect/disconnect an active device
While in the device list menu, you may
connect or disconnect your active device.
1. Press MENU/SELECT on the telephone
base in idle mode to enter the main
menu.
2. Press q CID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press q CID or p to
highlight Device list, then press
MENU/SELECT.
4. Press q CID or p to highlight a
device, then press MENU/SELECT.
5. Press q CID or p to highlight
Connect/Disconnect (whichever
is applicable), then press
MENU/SELECT. The telephone base
displays Device connected/Device
disconnected. You hear a confirmation
tone.
NOTE
• When your active device is connected,
you are prompted to select
Disconnect. When your active device
is disconnected, you are prompted to
select Connect.
Remove a paired device
When you already have 2 devices on the
device list and you want to add another
device, you must first delete one from
the list. You can only pair 2 cell phones
or one cell phone and one Bluetooth
headset.
To remove a paired device:
1. Press MENU/SELECT on the
telephone base in idle mode to enter
the main menu.
2. Press q CID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press q CID or p to
highlight Device list, then press
MENU/SELECT.
4. Press q CID or p to highlight
the desired device, then press
X/DELETE.
-OR-
• Press q CID or p to highlight
the desired device, then press
MENU/SELECT.
• Press q CID or p to
highlight Remove, then press
MENU/SELECT.
5. The telephone base displays Remove
Headset X? (Headset X represents
the device name of your Bluetooth
headset). Press MENU/SELECT to
confirm. The telephone base displays
Device removed from device list
and you hear a confirmation tone.
Download phonebook
You can download cell phone directory
(phonebook) entries to your IS8128/
IS8128-2/IS8128-3/IS8128-4/IS8128-
5/IS8128-11/IS8128-21/IS8128-31/
IS8128-41/IS8128-51 telephone system
via Bluetooth wireless technology. Each
downloaded cell phone directory entry
are stored in the telephone phonebook
with up to 30 digits for each phone
number and 15 characters for each
name.
Before downloading a phonebook,
make sure the cell phone is paired,
active, and connected to your telephone
system. Place your cell phone next to the
telephone base when you download a
cell phone directory to your telephone
system.
To download a cell phone directory:
1. Press MENU/SELECT on the
telephone base in idle mode to enter
the main menu.
2. Press q CID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press q CID or p to highlight
Download dir, then press
MENU/SELECT. The handset displays
Select a device briefly.
• If there is no cell phone paired to
the system, the handset displays
Pair cell first and then returns to
the previous menu.
4. Press q CID or p to highlight a
device, then press MENU/SELECT.
To Next Page
Loading...
