Water Right Impression Plus Series

Questions and Answers

C
christopher53Sep 5, 2025
What does Err – 204 mean on my Water Right Impression Plus?
- G
  gatesmichaelSep 5, 2025
  If your Water Right Water Dispenser displays Err – 204, it means a leak has been detected. This occurs when the dP input is active for “ALARM” and the input is closed. The alarm buzzer will activate, and the screen will display the error. Check for a low flow leak. Press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position, or disconnect the power supply from the PC Board for 5 seconds and then reconnect to clear the error.
C
Chris BarajasSep 15, 2025
Why Water Right Impression Plus Water Dispenser control valve fails to draw in regenerant?
- A
  Alan MorrisSep 15, 2025
  If the Water Right Water Dispenser control valve fails to draw in regenerant, the injector may be plugged and needs replacement. Other potential causes include a faulty regenerant piston (which would also need replacement), a leak in the regenerant line connection (inspect for air leaks), a restricted drain line causing excess back pressure (inspect and remove any restrictions), a drain line that is too long or too high (shorten the length and/or height), or low water pressure (ensure it remains at a minimum of 25 psi).
C
Crystal SuttonAug 31, 2025
Why won't my Water Right Impression Plus Water Dispenser draw in regenerant?
- R
  Regina GutierrezAug 31, 2025
  If the control valve on your Water Right Water Dispenser isn't drawing in regenerant, consider the following: * The injector might be plugged: Remove and clean or replace the injector. * The regenerant piston could be faulty: Replace the regenerant piston. * There might be a leak in the regenerant line connection: Inspect the regenerant line for air leaks. * The drain line might be restricted, causing excess back pressure: Inspect the drain line and clean to correct the restriction. * The drain line might be too long or too high: Shorten the length or height. * The water pressure might be low: Check the incoming water pressure, which must remain at a minimum of 25 psi.
E
Ethan EsparzaSep 18, 2025
Why does time of day flashes on Water Right Water Dispenser?
- D
  Deborah ChavezSep 18, 2025
  If the time of day is flashing on and off on your Water Right Water Dispenser, it is due to a power outage. Reset the time of day. If the PC board has battery back up present the battery may be depleted. See front cover and drive assembly drawing for instructions.
A
Andrea MackSep 16, 2025
How to fix no display on Water Right Impression Plus PC board?
- C
  Charlotte RobinsonSep 16, 2025
  If the display on the Water Right Water Dispenser PC board is blank, it could be due to a depleted battery. See the Operating Display and Maintenance section for instructions. Ensure the control valve power adapter is plugged into the outlet and the power cord end is connected to the PC board connection. Verify the proper voltage is being delivered to the PC board. The power adapter or PC board may be defective, requiring replacement. Finally, check if there is power at the electric outlet; repair the outlet or use a working one.
N
nrosarioSep 23, 2025
How to fix Err – 204 error on Water Right Impression Plus Water Dispenser?
- P
  Patrick TrevinoSep 23, 2025
  If your Water Right Water Dispenser displays Err – 204, a leak detected error, which is viewable in history screens, and it occurs when the dP input is active for 'ALARM' and the input is closed, check for a low flow leak. Press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position, or disconnect the power supply from the PC Board for 5 seconds and then reconnect to clear the error.
S
Stephanie HenryAug 28, 2025
Why is water constantly running to the drain in my Water Right Impression Plus Water Dispenser?
- P
  Philip WardAug 28, 2025
  If water is constantly running to the drain in your Water Right Water Dispenser, it could be due to: * A power outage during regeneration: Upon power restoration, the control will finish the remaining regeneration time. Reset the time of day. If the PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * A damaged seal/stack assembly: Replace the seal/stack assembly. * Piston assembly failure: Replace the piston assembly. * The drive cap assembly not being tightened properly: Retighten the drive cap assembly.
J
Juan GomezAug 27, 2025
Why is my Water Right Impression Plus Water Dispenser using too much regenerant?
- M
  Mr. Clifford May MDAug 27, 2025
  If your Water Right Water Dispenser control valve is using too much regenerant, consider these possible causes: * Improper refill setting: Check the refill setting. * Improper program settings: Ensure the program settings are specific to the water quality and application needs. * Frequent regeneration: Check for leaking fixtures that may be exhausting capacity or the system is undersized.
W
williamjacksonAug 27, 2025
Why is there excessive water in my Water Right Water Dispenser's regenerant tank?
- D
  davidburkeAug 27, 2025
  If there's too much water in the regenerant tank of your Water Right Water Dispenser, here are possible causes: * Improper program settings: Check the refill setting. * Plugged injector: Remove and clean or replace the injector. * Drive cap assembly not tightened properly: Retighten the drive cap assembly. * Damaged seal/stack assembly: Replace the seal/stack assembly. * Restricted or kinked drain line: Check the drain line for restrictions or kinks and correct them. * Plugged backwash flow controller: Remove and clean or replace the backwash flow controller. * Missing refill flow controller: Replace the refill flow controller.
K
Karen WhiteAug 25, 2025
Why does my Water Right Water Dispenser regenerate at the wrong time?
- C
  Christopher GrantAug 26, 2025
  If your Water Right Water Dispenser control valve is regenerating at the wrong time, here's what could be happening: * **Power Outage:** Reset the time of day. If your PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * **Incorrect Time of Day Setting:** Reset the time of day to the correct time. * **Incorrect Regeneration Time Setting:** Reset the regeneration time. * **Control Valve Set to Immediate Regeneration:** Check the programming setting and reset to NORMAL for a delayed regeneration time. * **Control Valve Set to Both Delayed and Immediate Regeneration:** Check the programming setting and reset to NORMAL for a delayed regeneration time.

Water Right Impression Plus Series Specifications

General

Brand	Water Right
Model	Impression Plus Series
Category	Water Dispenser
Language	English

Summary

PRE-INSTALLATION INSTRUCTIONS FOR DEALERS

BYPASS VALVE

INSTALLATION

General Installation & Service Warnings

Crucial safety and service guidelines for installation.

Site Requirements

Essential conditions and specifications for the installation location.

Installation Types

Details steps for well water and municipal installations.

Plumbing Connections

Specifics for connecting water inlet and outlet lines.

PROGRAMMING PROCEDURES

Setting Time and Day

Steps to set the current time and day on the unit.

Core Programming Settings

Guide to configure hardness, regeneration frequency, and immediate regeneration.

Alarm and Display Settings

Configuration for service alarms, audible alarms, and backlight.

START-UP INSTRUCTIONS

Flushing of System

Steps to flush the system after installation.

Conditioning of Media

Process to prepare the system's media for use.

Sanitizing Unit

Procedure for sanitizing the water softener.

OPERATING DISPLAYS AND MAINTENANCE

Understanding System Displays

Explains the various user displays and navigation.

Regeneration Procedures

Details manual regeneration and the twin system's regeneration mode.

Maintenance and Troubleshooting

Covers power loss, salt checks, error messages, and brine tank care.

TROUBLESHOOTING GUIDE

SERVICE INSTRUCTIONS

TRANSFER CAP ASSEMBLIES SERVICE INSTRUCTIONS

Detailed steps for servicing transfer cap assemblies.

REPLACEMENT PARTS

FRONT COVER AND DRIVE ASSEMBLY

Lists parts for the front cover and drive assembly.

PISTON ASSEMBLY

Lists parts for the piston assembly.

IN;OUT HEAD (FOR TANK B)

Lists parts for the inlet/outlet head.

TWIN TRANSFER

Lists parts for the twin transfer system.

OPTIONAL CHLORINE GENERATOR ASSEMBLY

Lists parts for the optional chlorine generator.

BYPASS VALVE

Lists parts for the bypass valve assembly.

BRINE ELBOW ASSEMBLY

Lists parts for the brine elbow assembly.

SERVICE WRENCH - CV3193-02

Details the service wrench tool.

INJECTOR ASSEMBLIES

Lists various injector assemblies.

WATER METER AND METER PLUG

Lists parts for the water meter and plug.

DRAIN LINE ASSEMBLY 3;4

Lists parts for the 3/4" drain line assembly.

DRAIN LINE ASSEMBLY 1

Lists parts for the 1" drain line assembly.

BRINE TANK ASSEMBLY

Lists parts for the brine tank assembly.

SAFETY FLOAT BRINE ELBOW

Lists parts for the safety float brine elbow.

INTERCONNECT FITTING ASSEMBLY (UP TO 10″ TANKS)

Lists parts for interconnecting smaller tanks.

INTERCONNECT FITTING ASSEMBLY (12″ & LARGER TANKS)

Lists parts for interconnecting larger tanks.

PVC Elbow Fittings

Parts for PVC male NPT and solvent elbow fittings.

Brass Sweat Fittings

Parts for 1" and 3/4" brass sweat fittings.

Plastic Male Fittings

Parts for 1" and 1-1/4" plastic male fittings.

Larger Brass & PVC Fittings

Parts for 1-1/4" & 1-1/2" brass sweat and PVC solvent fittings.

Shark Bite Fittings

Parts for 3/4" and 1" brass Shark Bite fittings.

John Guest Elbow Fittings

Parts for 3/4" and 1" John Guest elbow fittings.

SANITIZER PLUS TWIN SPECIFICATIONS

ASP1 SPECIFICATIONS

Technical specifications for ASP1 series models.

ASP2 SPECIFICATIONS

Technical specifications for ASP2 series models.

CYCLE TIMES AND USAGE

Table detailing cycle times and salt usage for models.

IMPRESSION PLUS TWIN SPECIFICATIONS

IMP-TW Specifications

Technical specifications for Impression Plus Twin models.

IMPRC-TW Specifications

Technical specifications for Impression Plus Twin carbon models.

Cycle Times and Salt Usage

Table detailing cycle times and salt usage for IMP models.

Water Softener Limited Warranty

QUICK REFERENCE GUIDE

System Operation Overview

Overview of system displays and navigation.

Bypass Valve Operation

Instructions for operating the bypass valve.

Setting Time and Key Adjustments

Steps to reset time and adjust hardness, regeneration, and alarms.

Error Handling and Manual Regeneration

Information on error codes and initiating manual regeneration.

Related product manuals

Water Right Impression

16 pages

Water Right Impression Series

32 pages

Water Right Impression RC Series

Water Right IMPC-1035

32 pages

Water Right IM-1044

32 pages

Water Right Impression Plus Series - User Manual

Table of Contents

Questions and Answers

Water Right Impression Plus Series Specifications

Summary

PRE-INSTALLATION INSTRUCTIONS FOR DEALERS

BYPASS VALVE

INSTALLATION

General Installation & Service Warnings

Site Requirements

Installation Types

Plumbing Connections

PROGRAMMING PROCEDURES

Setting Time and Day

Core Programming Settings

Alarm and Display Settings

START-UP INSTRUCTIONS

Flushing of System

Conditioning of Media

Sanitizing Unit

OPERATING DISPLAYS AND MAINTENANCE

Understanding System Displays

Regeneration Procedures

Maintenance and Troubleshooting

TROUBLESHOOTING GUIDE

SERVICE INSTRUCTIONS

TRANSFER CAP ASSEMBLIES SERVICE INSTRUCTIONS

REPLACEMENT PARTS

FRONT COVER AND DRIVE ASSEMBLY

PISTON ASSEMBLY

IN;OUT HEAD (FOR TANK B)

TWIN TRANSFER

OPTIONAL CHLORINE GENERATOR ASSEMBLY

BYPASS VALVE

BRINE ELBOW ASSEMBLY

SERVICE WRENCH - CV3193-02

INJECTOR ASSEMBLIES

WATER METER AND METER PLUG

DRAIN LINE ASSEMBLY 3;4

DRAIN LINE ASSEMBLY 1

BRINE TANK ASSEMBLY

SAFETY FLOAT BRINE ELBOW

INTERCONNECT FITTING ASSEMBLY (UP TO 10″ TANKS)

INTERCONNECT FITTING ASSEMBLY (12″ & LARGER TANKS)

PVC Elbow Fittings

Brass Sweat Fittings

Plastic Male Fittings

Larger Brass & PVC Fittings

Shark Bite Fittings

John Guest Elbow Fittings

SANITIZER PLUS TWIN SPECIFICATIONS

ASP1 SPECIFICATIONS

ASP2 SPECIFICATIONS

CYCLE TIMES AND USAGE

IMPRESSION PLUS TWIN SPECIFICATIONS

IMP-TW Specifications

IMPRC-TW Specifications

Cycle Times and Salt Usage

Water Softener Limited Warranty

QUICK REFERENCE GUIDE

System Operation Overview

Bypass Valve Operation

Setting Time and Key Adjustments

Error Handling and Manual Regeneration

Related product manuals