Watlow 97 series - Page 53

Active if Output 4 is equipped for
communications (96 _ _-_ _ _ R-
_ _ _ _ or 96 _ _-_ _ _ U-_ _ _ _)
and Setup Page Lock (Lockout
Menu) is not set to [hide].
none*
[9600][1200] 1200
[2400] 2400
[4800] 4800
[9600] 9600
[1(20] 19.2K
[bAUd] Baud Rate
Sets
communications
baud rate.
Active if Output 4 is retransmit
(97 _ _-_ _ _ M-_ _ _ _), and
Analog Output 4 (Output 4
Menu) is set to [`yes] and
Setup Page Lock (Lockout
Menu) is not set to [hide].
none*0
-1999 to 9999
[ACAL] Analog Output
Offset
Sets analog output
offset.
Active if Output 4 is equipped for
retransmit (97 _ _-_ _ _ M-_ _ _ _),
and Analog Output 4 (Output 4
Menu) is set to [`yes] and
Setup Page Lock (Lockout
Menu) is not set to [hide].
none*999Analog Range Low to
9999
[A`hi] Analog Output
High
Sets analog output
range high scaling.
Active if Output 4 is equipped for
retransmit (97 _ _-_ _ _ M-_ _ _ _),
and Analog Output 4 (Output 4
Menu) is set to [Proc] and
Setup Page Lock (Lockout
Menu) is not set to [hide].
none*-999-1999 to Analog Range
High
[A`Lo] Analog Output
Low
Sets analog output
range low scaling.
Active if Output 4 is equipped for
retransmit (97 _ _-_ _ _ M-_ _ _ _)
and Setup Page Lock (Lockout
Menu) is not set to [hide].
none*
[4-20][4-20] 4-20 mA
[0-20] 0-20 mA
[0-`5] 0-5VÎ (dc)
[1-`5] 1-5VÎ (dc)
[0-10] 0-10VÎ (dc)
[Prc4] Process 4 Type
Sets process 4 out-
put type.
Active if Output 4 is equipped for
retransmit (97 _ _-_ _ _ M-_ _ _ _)
and Setup Page Lock (Lockout
Menu) is not set to [hide].
none*
[proc][``no] not active
[proc] process
[Aout] Analog Output 4
Selects output 4
retransmit signal.
Active if Output 4 is equipped for
a relay (97 _ _-_ _ _ D-_ _ _ _),
Output 4 is Set to [``AL]
(Alarm) and Setup Page Lock
(Lockout Menu) is not set to
[hide].
none*
[`yes][``no] no
[`Yes] yes
[Anu4] Alarm
Annunciation 4
Selects alarm 4
annunciation option.
Active if Output 4 is equipped for
a relay (97 _ _-_ _ _ D-_ _ _ _),
Output 4 (Output 4 Menu) is
set to [``AL] (Alarm) and
Setup Page Lock (Lockout
Menu) is not set to [hide].
none*
[al`0][al`0] alarm condition
de-energizes output
[al`C] alarm condition
energizes output
[Lgc4] Alarm Logic 4
Selects alarm 4
output condition in
alarm state.
Watlow Series 97 Parameters ■ 6.13
Setup Page / Output 4 Menu
Display Parameter Range Default Modbus Conditions for
Address Parameters to Appear
read/write
NOTE: For more information about how parameter seetings affect the controller’s operation, see Chapter Five, Features.
*Output 4 parameters cannot
be changed with the Modbus
interface.