Series 97 Fold-out Software Map
[``97] Process Value
[Safe]
Home Page
Limit Status
Setup Page
[InP1]
Input 1 Menu
[`SEt]
Setup Page
[SEn1] Sensor Type 1____________
[In`1] Input 1 __________________
[rL`1] Range Low 1 _____________
[rh`1] Range High 1 _____________
[dEC1] Decimal 1 ________________
[Ftr1] Input Software Filter 1 ______
[InP2]
Input 2 Menu
[`SEt]
Setup Page
[In`2] Input 2 __________________
[E`Fn] Event Function ____________
[E`cn] Event Condition ___________
[Out1]
Ouput 1 Menu
[`SEt]
Setup Page
[LSid] Set Limit Active Sides ______
[LhyS] Limit Hysteresis ___________
[Out2]
Ouput 2 Menu
[`SEt]
Setup Page
[Ot`2] Output 2 _________________
[hys2] Alarm Hysteresis 2 _________
[LAt2] Latching 2 _______________
[sil2] Silencing 2 _______________
[Sid2] Alarm Active Sides 2 _______
[Lgc2] Alarm Logic 2 _____________
[Anu2] Alarm Annunciation 2 _______
[Out3]
Ouput 3 Menu
[`SEt]
Setup Page
[Ot`3] Output 3 _________________
[hys3] Alarm Hysteresis 3 _________
[LAt3] Latching 3 _______________
[sil3] Silencing 3 _______________
[sid3] Alarm Active Sides 3 _______
[Lgc3] Alarm Logic 3 _____________
[Anu3] Alarm Annunciation 3 _______
[Out4]
Ouput 4 Menu
[`SEt]
Setup Page
[Ot`4] Output 4 _________________
[hys4] Alarm Hysteresis 4 _________
[LAt4] Latching 4 _______________
[sil4] Silencing 4 _______________
[Sid4] Alarm Active Sides 4 _______
[Lgc4] Alarm Logic 4 _____________
[Anu4] Alarm Annunciation 4 _______
[Aout] Analog Output 4 ___________
[Prc4] Process 4 Type ___________
[A`hi] Analog Output High ________
[A`lo] Analog Output Low ________
[ACAL] Analog Output Offset _______
[BaUd] Baud Rate _______________
[Addr] Address _________________
[diSP]
Display Menu
[`SEt] Setup Page
[UdSP] Upper Display_____________
[UP`L] Upper Display
User Limit Message________
[LdSP] Lower Display_____________
[Lo`S] Lower Display
User Safe Message________
[Lo`L] Lower Display
User Limit Message___
_____
[GLbL]
Global Menu
[`SEt]
Setup Page
[
C-F`] C or F ___________________
[`Err] Input Error Latching ________
Operations Page
[LIM] Limit Menu
[OPEr] Operations Page
[L~Lo] Low Limit Set Point _________
[L~hi] High Limit Set Point _________
[CAL1] Calibration Offset ___________
[Mon] Monitor Menu
[OPEr] Operations Page
[Pr1`] Process 1_________________
[L`St] Limit Status_______________
[AL`2] Alarm 2 Status _____________
[AL`3] Alarm 3 Status _____________
[AL`4] Alarm 4 Status _____________
[E`St] Event Input Status __________
[ALM] Alarm Menu
[OPEr] Operations Page
[A2Lo] Alarm 2 Low _______________
[A2hi] Alarm 2 High ______________
[A3Lo] Alarm 3 Low _______________
[A3hi] Alarm 3 High ______________
[A4Lo] Alarm 4 Low _______________
[A4hi] Alarm 4 High ______________
Factory Page
[`LOC]
Lockout Menu
[FctY] Factory Page
[OPEr] Operations Page Mode _______
[`SEt] Setup Page Lock ___________
[`CAL] Calibration Menu Lock _______
[dIAg] Diagnostics Menu
[FctY] Factory Page
[MdL] Model Number _____________
[dAtE] Date of Manufacture _________
[`Sn1] Serial Number 1 ____________
[`Sn2] Serial Number 2 ____________
[Soft] Software ID Number _________
[`rEu] Software Revision ___________
[ity2] Input 2 Hardware Enabled_____
[OTY1] Output 1 Hardware __________
[Oty2] Output 2 Hardware __________
[Oty3] Output 3 Hardware __________
[Oty4] Output 4 Hardware __________
[tout] Test Output ________________
[dISP] Test Displays _______________
[hrES] High Resolution ____________
[AMb] Ambient Temperature ________
[Acnt] Ambient A-D Counts _________
[cnt1] Channel 1 A-D Counts _______
[cnt2] Channel 2 A-D Counts _______
[LinE] Line Frequency _____________
Enter your settings on a photocopy
of this page.
The Factory Page also includes
calibration parameters that are
not necessary for everyday use of
the controller. Calibration parame-
ters and procedures are explained
in the Appendix.
To Next Page
Loading...
