Weinmann ACCUVAC Basic

Other manuals for Weinmann ACCUVAC Basic

Service And Repair Instructions32 pages

Quick Start Guide2 pages

Questions and Answers

K
Kevin BrockAug 7, 2025
What to do if Weinmann Medical Equipment is not charging?
- K
  Kaitlyn DelgadoAug 7, 2025
  If your Weinmann Medical Equipment is not charging, there are several potential causes. First, the AC adapter/charger plug may be defective, requiring professional repair. Second, the external power supply might be inadequate; ensure it's between 12.0 and 13.8 volts. Third, check fuses F1 and F2, or the fuse in the vehicle plug, and replace if defective. Finally, verify that the snap-in connection between the circuit board and power pack is properly engaged.
J
janetdonaldsonAug 11, 2025
Why Weinmann ACCUVAC Basic Medical Equipment does not start, and the O/I indicator does not show ready for operation?
- M
  Michael JohnsonAug 11, 2025
  If your Weinmann Medical Equipment isn't starting and the O/I indicator isn't lit, check the following: First, replace fuse F1 or F2 in the appliance, or the fuse in the vehicle plug, if defective. Next, if the power pack is fully discharged, perform several charge/discharge cycles, and replace the power pack if this doesn't work. Also, ensure the vehicle power socket has the correct polarity, correcting it and replacing fuse F1 if necessary. Finally, make sure the snap-in connection between the circuit board and power pack is properly engaged.
W
William Villanueva DDSAug 15, 2025
What to do if Weinmann Medical Equipment does not reach maximum vacuum?
- R
  rodriguezamyAug 15, 2025
  If your Weinmann Medical Equipment does not reach the maximum vacuum of –0.8 bar in 20 seconds, but the voltage indicator shows ready for operation, first check all tubes are firmly connected and the disposable bag is securely installed to rule out leaks in the suction side of the appliance. If not, charge the power pack. If the issue persists, there may be a fault in the pump, requiring professional repair.
T
Tammy CarpenterAug 19, 2025
How to fix the Weinmann ACCUVAC Basic Medical Equipment if the top LED of voltage indicator lights up after charging, but pump does not run when powered by power pack?
- A
  Angelica DaughertyAug 20, 2025
  If the top LED of the voltage indicator lights up after charging, but the pump doesn't run when powered by the power pack, check the internal connection between the printed circuit board (X1) and the power pack. Also, replace fuse F2 if it is defective.
A
Alexander LarsenAug 25, 2025
Why Weinmann ACCUVAC Basic Medical Equipment power pack is not fully charged after charging for 14 hours?
- A
  Angela KellerAug 26, 2025
  If the power pack in your Weinmann Medical Equipment isn't fully charged after 14 hours, and the top LED in the voltage indicator doesn't light up, ensure you are using the correct charger: AC adapter/charger plug WM 10750 or charger WM 2645. Verify that the vehicle electrical system is supplying between 12.0 – 13.8 V. The power pack may also be damaged from being fully discharged, requiring replacement.
M
Michael ReyesAug 28, 2025
What causes Fuse F2 to frequently blow in Weinmann ACCUVAC Basic?
- K
  kaylahullAug 28, 2025
  Fuse F2 in your Weinmann Medical Equipment might frequently blow because the pump is often switched on under vacuum conditions, so avoid switching on the pump under vacuum. Alternatively, the pump may be defective, requiring professional repair.
H
Heidi WalkerSep 2, 2025
What to do if Weinmann Medical Equipment does not start, but O/I indicator and voltage indicator show ready for operation?
- A
  Anthony LunaSep 2, 2025
  If your Weinmann Medical Equipment does not start, but the O/I indicator and voltage indicator show ready for operation, the pump may be faulty. Have repairs carried out by factory or by expert personnel.