Yamaha MagicStomp - Effect Parameters; Distortion; Digital Distortion

4
Effect Parameters
Distortion
Advanced distortion. Mainly used for direct connection to guitar amp’s front input.
Digital Distortion
Distortion effect. Mainly used for direct connection to guitar amp’s front input.
Parameter Display Range Description
Type TYPE
Lead1, Lead2, Drive1, Drive2,
Crunch1, Crunch2, Fuzz1,
Fuzz2, Distortion1, Distortion2,
Overdrive1, Overdrive2, Tube,
Solidstate
Distortion type
Gain GAIN 0.0 to 10.0 Adjusts the amount of distortion
Master MSTR 0.0 to 10.0 Adjusts the volume
Tone TONE 0.0 to 10.0 Adjusts the tone
EQ 1 Freq. EQ1F 50.0 to 400 Hz Specifies the post effect EQ1 frequency
EQ 1 Gain EQ1G -12.0 to 12.0 dB Specifies the post effect EQ1 gain
EQ 1 Q EQ1Q 0.100 to 20.0 Specifies the post effect EQ1 Q (bandwidth)
EQ 2 Freq. EQ2F 200 to 1.60 kHz Specifies the post effect EQ2 frequency
EQ 2 Gain EQ2G -12.0 to 12.0 dB Specifies the post effect EQ2 gain
EQ 2 Q EQ2Q 0.100 to 20.0 Specifies the post effect EQ2 Q (bandwidth)
EQ 3 Freq. EQ3F 600 to 4.80 kHz Specifies the post effect EQ3 frequency
EQ 3 Gain EQ3G -12.0 to 12.0 dB Specifies the post effect EQ3 gain
EQ 3 Q EQ3Q 0.100 to 20.0 Specifies the post effect EQ3 Q (bandwidth)
EQ 4 Freq. EQ4F 2.00 k to 16.0 kHz Specifies the post effect EQ4 frequency
EQ 4 Gain EQ4G -12.0 to 12.0 dB Specifies the post effect EQ4 gain
EQ 4 Q EQ4Q 0.100 to 20.0 Specifies the post effect EQ4 Q (bandwidth)
Pre EQ Level PELV 0.0 to 10.0 Specifies the pre effect EQ level
Pre EQ 1 Freq. PE1F 50.0 to 500 Hz Specifies the pre effect EQ1 frequency
Pre EQ 1 Gain PE1G -12.0 to 12.0 dB Specifies the pre effect EQ1 gain
Pre EQ 1 Q PE1Q 0.100 to 20.0 Specifies the pre effect EQ1 Q (bandwidth)
Pre EQ 2 Freq. PE2F 200 to 2.00 Hz Specifies the pre effect EQ2 frequency
Pre EQ 2 Gain PE2G -12.0 to 12.0 dB Specifies the pre effect EQ2 gain
Pre EQ 2 Q PE2Q 0.100 to 20.0 Specifies the pre effect EQ2 Q (bandwidth)
Pre EQ 3 Freq. PE3F 1.00 k to 10 kHz Specifies the pre effect EQ3 frequency
Pre EQ 3 Gain PE3G -12.0 to 12.0 dB Specifies the pre effect EQ3 gain
Pre EQ 3 Q PE3Q 0.100 to 20.0 Specifies the pre effect EQ3 Q (bandwidth)
N. G. Threshold NGTH 0.0 to 10.0 Level at which the noise gate activates
N. G. Attack NGAT 0 to 120 ms Time required for the noise gate to open after signal exceeds threshold
N. G. Hold NGHL 0.02 to 2040 ms Time noise gate stays open
N. G. Decay NGDC 6 to 44500 ms
Time required for the noise gate to close after signal goes below thresh-
old
Parameter Display Range Description
Type TYPE
Distortion1, Distortion2,
Overdrive1, Overdrive2,
Crunch
Distortion type
Drive DRV 0 to 100 Distortion drive
Master MSTR 0 to 100 Master volume
Tone TONE –10 to +10 Tone
Noise Gate NG 0 to 20 Noise reduction