YASKAWA L1000E - Page 175

B Parameter Table
YASK AWA TOEPYAIL1E01A YASKAWA AC Drive L1000E Quick Start Guide 175
Parameter Table
B
E4: Motor 2 Parameters
These parameters are hidden when a PM motor control mode has been selected for motor 1 (A1-02 = 7).
E5: PM Motor Settings
No.(Addr.) Name Description Setting
E4-01
(321H)
<4> Default setting value is dependent on the drive model (o2-04).
<10> The display resolution depends on the rated output power of the drive. Models 2A0018 to 2A0041 and 4A0009 to 4A0023 display values in
0.01 A units, while models 2A0059 to 2A0432 and 4A0030 to 4A0260 display values in 0.1 A units.
Motor 2 Rated Current
Sets the full load current for motor 2. Automatically set during Auto-Tuning.
Default:
<4>
Min: 10% of drive
rated current
Max: 200% of drive
rated current
<10>
E4-02
(322H)
Motor 2 Rated Slip
Sets the rated slip for motor 2. Automatically set during Auto-Tuning.
Default:
<4>
Min: 0.00 Hz
Min: 20.00 Hz
E4-03
(323H)
Motor 2 Rated No-Load
Current
Sets the no-load current for motor 2. Automatically set during Auto-Tuning.
Default:
<4>
Min: 0 A
Min: [E4-01]
<10>
E4-04
(324H)
Motor 2 Motor Poles
Sets the number of poles of motor 2. Automatically set during Auto-Tuning.
Default: 4
Min: 2
Max: 48
E4-05
(325H)
Motor 2 Line-to-Line
Resistance
Sets the phase-to-phase resistance for motor 2. Automatically set during
Auto-Tuning.
Default:
<4>
Min: 0.000 Ω
Max: 65.000 Ω
E4-06
(326H)
Motor 2 Leakage Inductance
Sets the voltage drop for motor 2 due to motor leakage inductance as a
percentage of rated voltage. Automatically set during Auto-Tuning.
Default:
<4>
Min: 0.0%
Max: 40.0%
No.(Addr.) Name Description Setting
E5-02
(32AH)
<1>
Motor Rated Power
Sets the rated capacity of the motor.
Default: <2>
Min: 0.10 kW
Max: 650.00 kW
E5-03
(32BH)
<1>
Motor Rated Current
Sets the motor rated current.
Default:
<2>
Min: 10% of drive
rated current
Max: 200% of drive
rated current
<3>
E5-04
(32CH)
<1>
Number of Motor Poles
Sets the number of motor poles.
Default: 12
Min: 2
Max: 120
<4>
E5-05
(32DH)
<1>
Motor Stator Resistance
(Single Phase)
Sets the stator resistance (1 phase value).
Default:
<2>
Min: 0.000 Ω
Max: 65.000 Ω
E5-06
(32EH)
<1>
Motor d-Axis Inductance
Sets the d-axis inductance.
Default:
<2>
Min: 0.00 mH
Max: 600.00 mH
E5-07
(32FH)
<1>
Motor q-Axis Inductance
Sets the q-axis inductance.
Default: <2>
Min: 0.00 mH
Max: 600.00 mH
E5-09
(331H)
<1>
Motor Induction Voltage Constant 1
Sets the induced phase peak voltage in units of 0.1 mV (rad/s) [electrical angle].
When setting this parameter, E5-24 should be set to 0.0.
Default:
<2>
Min: 0.0 mV/(rad/s)
Max:
6500.0 mV/(rad/s)
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV
common
_
CLV
CLV/PM
V/f OLV