YASKAWA L1000H - Page 49

11 UL Standards
YASKAWA Europe TOEP C710616 92D AC Drive L1000H Quick Start Guide EN 49
Note: Use crimp insulated terminals or insulated shrink tubing for wiring connections. Wires should have a continuous maximum
allowable temperature of 75C 600 Vac UL-approved vinyl-sheathed insulation.
 Installing Input Fuses
NOTICE: If a fuse is blown or a Residual Current Device (RCD) is tripped, check the wiring and the selection of the peripheral devices
to identify the cause. Contact YASKAWA before restarting the drive or the peripheral devices if the cause cannot be identified.
 Factory Recommended Branch Circuit Protection
YASKAWA recommends installing one of the following types of branch circuit protection to maintain compliance with
UL508C. Semiconductor protective type fuses are preferred. Alternate branch circuit protection devices are also listed
below.
6 AWG
M4 14-NK4 YA-4 AD-902 TP-014 100-054-033
M5 R14-5 YA-4 AD-902 TP-014 100-054-034
M6 R14-6 YA-5 AD-952 TP-014 100-051-261
M8 R14-8 YA-5 AD-952 TP-014 100-054-035
4 AWG
M6 R22-6 YA-5 AD-953 TP-022 100-051-262
M8 R22-8 YA-5 AD-953 TP-022 100-051-263
3/2/1 AWG
M8 R38-8 YA-5 AD-954 TP-038 100-051-264
M10 R38-10 YA-5 AD-954 TP-038 100-061-114
1/0 AWG
1/0 AWG  2P
M8 R60-8 YA-5 AD-955 TP-060 100-051-265
M10 R60-10 YF-1, YET-300-1 TD-321, TD-311 TP-060 100-051-266
2/0 AWG
2/0 AWG  2P
M10 70-10 YF-1, YET-300-1 TD-323, TD-312 TP-080 100-054-036
1 AWG  2P
2 AWG  2P
M10 38-L10 YF-1, YET-150-1 TD-224, TD-212 TP-038 100-051-556
3/0 AWG M10 80-10 YF-1, YET-300-1 TD-323, TD-312 TP-080 100-051-267
3/0 AWG  2P M10 80-L10 YF-1, YET-150-1 TD-227, TD-214 TP-080 100-051-557
4/0 AWG M10 R100-10
YF-1, YET-300-1
YF-1, YET-150-1
TD-324, TD-312
TD-228, TD-214
TP-100 100-051-269
4/0 AWG  2P M10 100-L10 YF-1, YET-150-1 TD-228, TD-214 TP-100 100-051-559
250 / 300 kcmil M10 R150-10 YF-1. YET-150-1 TD-229, TD-215 TP-150 100-051-272
250 kcmil  2P
300 kcmil  2P
M10 150-L10 YF-1, YET-150-1 TD-229, TD-215 TP-150 100-051-561
350 kcmil M10 180-10 YF-1, YET-300-1 TD-326, TD-313 TP-200 100-066-687
400 kcmil M10 200-10 YF-1, YET-300-1 TD-327, TD-314 TP-200 100-051-563
500 kcmil
600 / 650 kcmil
500 kcmil  2P
600 kcmil  2P
M10 325-10 YF-1, YET-300-1 TD-328, TD-315 TP-325 100-051-565
<1> Codes refer to a set of three crimp terminals and three insulation caps. Prepare input and output wiring using two sets for each connection.
Example 1: Models with 300 kcmil for both input and output require one set for input terminals and one set for output terminals, so the user
should order two sets of [100-051-272].
Example 2: Models with 4/0 AWG  2P for both input and output require two sets for input terminals and two sets for output terminals, so the
user should order four sets of [100-051-560].
Drive Model
CIMR-L
L1000H in Heavy Duty Mode (C6-01 = 0)
AC Drive Input
Amps
MCCB Rating
Amps <1>
Time Delay Fuse
Rating Amps <2>
Non-time Delay
Fuse Rating
Amps <3>
Bussmann
Semiconductor
Fuse Rating (Fuse
Ampere)
Three-Phase 400 V Class
40005 4.4 15 7 12 FWH-70B (70)
40006 6 15 10 17.5 FWH-70B (70)
40009 10.4 20 17.5 30 FWH-90B (90)
40015 15 30 25 40 FWH-80B (80)
40018 20 40 35 60 FWH-100B (100)
40024 29 50 50 80 FWH-125B (125)
Wire Gauge
Terminal
Screws
Crimp Terminal
Model Number
Tool
Insulation Cap
Model No.
Code <1>
Machine No. Die Jaw