Yealink SIP-T40G Administrator's Guide

Call Features
362
Parameter
dialplan.digitmap.apply_to.forward <y0000000000xx>.cfg
Description
It enables or disables the digit map to be applied to the numbers that you want to forward to when per-
forming call forward.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.apply_to.forward”
takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled, the incoming calls will be forwarded to the desired destination number according to the
string of the digit map.
Default
1
Parameter
dialplan.digitmap.apply_to.press_send <y0000000000xx>.cfg
Description
It enables or disables the entered number to match the predefined string of the digit map after press-
ing a send key. It is only applicable to the off-hook dialing.
The off-hook dialing includes: pick up the handset, press the Speakerphone key or press the line key
when the phone is idle.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.apply_to.press_send”
takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Parameter
dialplan.digitmap.apply_to.prefix_key <y0000000000xx>.cfg
Description
It enables or disables the phone to apply the predefined string of the digit map after pressing a Prefix
key.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled).
Permitted
Values
0-Disabled
1-Enabled
Default
1
Digit Map for a Specific Line Configuration
The following table lists the parameters you can use to configure the digit map for a specific line.
Parameter
account.X.dialplan.digitmap.enable
[1]
<MAC>.cfg
Description
It enables or disables the digit map feature for a specific account.
Note: The value configured by the parameter “account.X.dialplan.digitmap.enable” takes precedence
over that configured by the parameter “dialplan.digitmap.enable”.
Permitted
Values
0-Disabled
1-Enabled
Default
Blank
Parameter
account.X.dialplan.digitmap.string
[1]
<MAC>.cfg
Description
It configures the digit map pattern used for the dial plan.
Example:
account.1.dialplan.digitmap.string = <[2-9]x:86>3.T|0x.!|1xxx

Yealink SIP-T40G Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Wall mountable	Yes
Wi-Fi	No
Security algorithms	AES, HTTPS, SSL/TLS
Networking standards	IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP, TFTP, HTTP, HTTPS
Voice codecs	G.711, G.711a, G.711u, G.722, G.726, G.729ab
RJ-11 ports quantity	1
Ethernet LAN (RJ-45) ports	2
AC adapter input voltage	100 - 240 V
AC adapter output current	0.6 A
AC adapter output voltage	5 V
Power consumption (typical)	1.6 W
Certification	CE, FCC, ISO 9001
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 90 %
Volume control	Digital
Display diagonal	2.3 \
Display resolution	132 x 64 pixels
Lines quantity	3 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	3
Number of handles included	1 pc(s)

Weight and Dimensions

Depth	175 mm
Width	212 mm
Height	54 mm