EasyManuals Logo

Yealink SIP-T40G Administrator's Guide

Yealink SIP-T40G
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #483 background imageLoading...
Page #483 background image
Advanced Features
480
Variable Value Phone Action
swFwdOn=xxx=n
phone (“xxx” means the destination number)
The valid value of “n means the duration time (seconds) before for-
warding incoming calls (n is the times of 6, for example, 24). It is only
applicable to no answer forward feature.
Note: For Yealink phones, it works only if “features.fwd.allow” is set
to 1 (Enabled) and call forward mode is Phone, the always/busy/no
answer forward feature will apply to all the accounts on the phone.
Example:
http://10.10.20.10/servlet?key=NoAnswFwdOn=1001=24
AlwaysFwdOff/BusyFwdOff/NoAnswFwdOff
Deactivate the always/busy/no answer forward feature for the IP
phone.
Note: For Yealink phones, it works only if “features.fwd.allow” is set
to 1 (Enabled) and call forward mode is Phone, the always/busy/no
answer forward feature will apply to all the accounts on the phone.
Example:
http://10.10.20.10/servlet?key=NoAnswFwdOff
CALLEND/CallEnd End a call.
ASW/CANCEL/HOLD/UNHOLD:xxx
Answer/end/hold/unhold a call (xxx refers to the call-id of the active
call).
Example:
http://10.10.20.10/servlet?key=ASW:33093
Note: To get the call-id of the active call, configure the action URL:
http(s)://<serverIPAddress>/help.xml?CallId=$call_id. For more
information, refer to Action URL.
ACDlogin
Log into the ACD system.
Note: When ACD authentication information is required, the valid
URI is: http(s)://<-
phoneIPAd-
dress>/servlet?key=ACDlogin&agentID=xxx&password=xxx. When
ACD authentication information is not required, the valid URI is: http
(s)://<phoneIPAddress>/servlet?key=ACDlogin.
ACDlogout Log out of the ACD system.
SWAP
Swap to the held call when there is an active call and a held call on
the phone.
SPLIT
Split the local conference call into individual calls. After the split, the
conference call ends, and other parties are held.
Note: It is not available for network conference.
[1]
X is the line key ID. For T57W/T48U/T48S/T48G, X=1-29; for T54W/T46U/T46S/T46G/T29G, X=1-27; for
T53W/T53/T43U/T27G, X=1-21; for T42U/T42G/T42S/T41P/T41S, X=1-15; for T40P/T40G/T23P/T23G, X=1-3; for
T21(P) E2, X=1-2.
Action URI Configuration
The following table lists the parameters you can use to configure action URI.

Table of Contents

Other manuals for Yealink SIP-T40G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T40G and is the answer not in the manual?

Yealink SIP-T40G Specifications

General IconGeneral
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Wall mountableYes
Wi-FiNo
Security algorithmsAES, HTTPS, SSL/TLS
Networking standardsIEEE 802.3af
Ethernet LAN interface typeGigabit Ethernet
Supported network protocolsFTP, TFTP, HTTP, HTTPS
Voice codecsG.711, G.711a, G.711u, G.722, G.726, G.729ab
RJ-11 ports quantity1
Ethernet LAN (RJ-45) ports2
AC adapter input voltage100 - 240 V
AC adapter output current0.6 A
AC adapter output voltage5 V
Power consumption (typical)1.6 W
CertificationCE, FCC, ISO 9001
Operating temperature (T-T)-10 - 50 °C
Operating relative humidity (H-H)10 - 90 %
Volume controlDigital
Display diagonal2.3 \
Display resolution132 x 64 pixels
Lines quantity3 lines
Phonebook capacity1000 entries
Number of VoIP accounts3
Number of handles included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth175 mm
Width212 mm
Height54 mm

Related product manuals