Yealink SIP-T40G Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
369
Description
It configures the type of location request message.
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is set to HELD.
Permitted
Values
SIMPLE or REDSKY
If it is set to SIMPLE, the phone will send the location request message defined in RFC5985.
If it is set to REDSKY, the phone will send the location request message defined by REDSKY.
Default
SIMPLE
Parameter
dialplan.emergency.held.request_element.X.name
[2]
<y0000000000xx>.cfg
Description
It configures the custom element name to be sent in a location request message.
Example:
dialplan.emergency.held.request_element.1.name = mac
dialplan.emergency.held.request_element.2.name = companyID
dialplan.emergency.held.request_element.3.name = nai
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is set to HELD.
Permitted
Values
String
Default
Blank
Parameter
dialplan.emergency.held.request_element.X.value
[2]
<y0000000000xx>.cfg
Description
It configures the custom element value to be sent in a location request message.
Example:
dialplan.emergency.held.request_element.1.value = 001565B38ECB
dialplan.emergency.held.request_element.2.value = 6f2f2d50-c385-4b72-b84a-ce0ca3a77cb7
dialplan.emergency.held.request_element.3.value = 8611@pbx.yealink.com
Note: It works only if “dialplan.emergency.enable” is set to 1 (Enabled) and “dial-
plan.emergency.asserted_id_source” is set to HELD.
Permitted
Values
String
Default
Blank
Parameter
account.X.reg_with_pani_header.enable
[3]
<MAC>.cfg
Description
It enables or disables the phone to carry the PANI header in the REGISTER request message.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Parameter
account.X.invite_with_pani_header.enable
[3]
<MAC>.cfg
Description
It enables or disables the phone to carry the PANI header in the INVITE request message.
The PANI header format is:
P-Access-Network-Info:IEEE-802.3; eth-location=<MAC Address Of The Phone > ; local-time-zone-
e=”0800”

Yealink SIP-T40G Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Wall mountable	Yes
Wi-Fi	No
Security algorithms	AES, HTTPS, SSL/TLS
Networking standards	IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP, TFTP, HTTP, HTTPS
Voice codecs	G.711, G.711a, G.711u, G.722, G.726, G.729ab
RJ-11 ports quantity	1
Ethernet LAN (RJ-45) ports	2
AC adapter input voltage	100 - 240 V
AC adapter output current	0.6 A
AC adapter output voltage	5 V
Power consumption (typical)	1.6 W
Certification	CE, FCC, ISO 9001
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 90 %
Volume control	Digital
Display diagonal	2.3 \
Display resolution	132 x 64 pixels
Lines quantity	3 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	3
Number of handles included	1 pc(s)

Weight and Dimensions

Depth	175 mm
Width	212 mm
Height	54 mm