EasyManuals Logo

Yealink SIP-T46U Administrator's Guide

Yealink SIP-T46U
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #394 background imageLoading...
Page #394 background image
Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
391
Description
It enables or disables the DND feature synchronization for account X.
Note: The value configured by this parameter takes precedence over that configured by the parameter
"features.dnd.feature_key_sync.enable". It works only if “account.X.feature_key_sync.enable is set to
1 (Enabled).
Permitted
Values
0-Disabled
1-Enabled, server-based DND is enabled. Server and local phone DND are synchronized.
Default
Blank
Supported
Devices
All phones except T48G, T46G, T42G, T41P, T29G and CP920
Parameter
features.dnd.feature_key_sync.local_processing.enable <y0000000000xx>.cfg
Description
It enables or disables the local DND when DND feature synchronization is enabled.
Note: It works only if “features.feature_key_sync.enable and “features.dnd.feature_key_sync.enable
are set to 1 (Enabled). The value configured by the parameter “account.X.features.dnd.feature_key_
sync.local_processing.enable” takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled, DND is performed on the server side only.
1-Enabled, DND is performed on both the server side and locally.
Default
0
Parameter
account.X.features.dnd.feature_key_sync.local_processing.enable
[1]
<MAC>.cfg
Description
It enables or disables the local DND when DND feature synchronization is enabled.
Note: It works only if “features.feature_key_sync.enable and “features.dnd.feature_key_sync.enable
are set to 1 (Enabled).
Permitted
Values
0-Disabled, DND is performed on the server side only.
1-Enabled, DND is performed on both the server side and locally.
Default
Blank
[1]
X is the account ID. For T57W/T54W/T48U/T48S/T48G/T46U/T46S/T46G/T29G, X=1-16; for
T53W/T53/T43U/T42U/T42G/T42S, X=1-12; for T41P/T41S/T27G, X=1-6; for T40P/T40G/T23P/T23G, X=1-3; for T21
(P) E2, X=1-2.
Multiple Call Appearances
You can enable each registered line to support multiple concurrent calls. For example, you can place one call on
hold, switch to another call on the same registered line, and have both calls displayed.
You can set the maximum number of concurrent calls per line key on all-lines basis or a per-line basis. For
example, if you specify 3 concurrent-calls for account 1, you can only have three call appearances on a cor-
responding line key. The additional incoming calls will be rejected.
Note: The number of concurrent calls applies to all line keys. For example, if three line keys are associated with an account,
you can have three call appearances per line key.
Topic
Multiple Call Appearances Configuration
Multiple Call Appearances Configuration
You can specify the maximum concurrent calls per line key.
The following table lists the parameters you can use to configure multiple call appearances.

Table of Contents

Other manuals for Yealink SIP-T46U

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T46U and is the answer not in the manual?

Yealink SIP-T46U Specifications

General IconGeneral
Handset typeWireless handset
Product typeIP Phone
Product colorGray
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Expansion module supportYes
Ethernet LAN (RJ-45) ports2
Security algorithmsAES, HTTPS, SRTP, TLS
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Front camera-
AC adapter input voltage100 - 240 V
Display diagonal4.3 \
Display resolution480 x 272 pixels
Lines quantity- lines
Phonebook capacity1000 entries
Number of VoIP accounts16
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Voice codecsAGC, AJB, AMR-WB, CNG, G.711, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Number of handles included1 pc(s)
Harmonized System (HS) code85171800
Weight and Dimensions IconWeight and Dimensions
Depth213 mm
Width244 mm
Height185 mm

Related product manuals