Agilent Technologies 86100A User Manual

Index-8
Index
TEDGe?, 18-43
TER?, 4-14
Test (*TST?), 3-13
TEST?, 15-9, 17-14
TIME?, 7-5, 7-7
TITLe?, 17-14
TMAX, 18-44
TMIN, 18-45
TVOLt?, 18-45
UEE?, 4-14
UER?, 4-14
ULIMit?, 15-10
UNITs OFFSet, 8-8
UNITs?, 8-7
VAMPlitude?, 18-46
VAVerage, 18-43, 18-46
VERTical OFFSet?, 12-8
VERTical RANGe, 12-9
VMAX?, 18-47
VMIN?, 18-48
VPP?, 18-48
VTIMe?, 18-49
VTOP?, 18-49
WAVelength?, 8-8
X1Position?, 14-5, 16-4
X1Y1source?, 16-4
X2Position?, 14-5, 16-4
X2Y2source?, 16-5
XDELta?, 16-2, 16-5
XUNits?,
16-5
Y1Position?, 14-6, 16-5
Y2Position?, 14-6
YDELta?, 16-6
YUNits?, 16-6
query
interrupt, 1-26
responses, formatting, 5-2
query error, 1-47
QYE Status Bit, 1-18
querying locked status, 9-2
question mark, 1-26
queue, output, 1-26
quotes, with embedded strings, 1-24
QYE bit, 3-4
R
RANGe, 8-6, 12-7
RATE, 9-7, 21-3
*RCL (Recall), 3-7
REACtance?, 16-2
RECall SETup, 4-12
receiving
common commands, 3-2
Recommend?, 7-8
recovery, clock, 9-2
register
save/recall, 3-7, 3-11
Standard Event Status Enable, 1-19
remote
local code and capability, 1-35
remote screen capture, 10-7
representation of infinity, 1-25
Request Control (RQC) status bit, 1-18
Request Service (RQS)
default, 1-34
status bit, 1-18
Reset (*RST), 3-7
resetting the parser, 1-35
RESPonse, 21-4
CALibrate, 21-4, 22-5
CALibrate CANCel, 21-5
CALibrate CONTinue, 21-5
HORizontal, 21-6
HORizontal POSition, 21-6
HORizontal RANGe, 21-6
RISetime, 21-7
TDRDest, 21-7
TDTDest, 21-8
VERTical, 21-9, 22-8
VERTical OFFSet, 21-9, 22-8
VERTical RANGe, 21-10, 22-8
response
data, 1-26
result state code, and SENDvalid, 18-40
RESults?, 18-37
retrieval and storage, 10-2
returning control to system controller,
1-35
revised commands, 1-42
rise time measurement setup, 18-2
RISetime, 18-40
RMS voltage, and VRMS, 18-48
Root level commands, 4-2
AEEN, 4-2
ALER?, 4-3
BLANk, 4-5
CDISplay, 4-5
COMMents, 4-5
CREE, 4-5
CRER?, 4-6
DIGitize, 4-6
LER?, 4-8
LTEE, 4-9
LTER?, 4-9
MODel?, 4-9
MTEE, 4-7, 4-10, 4-11
MTER?, 4-10, 4-12
OPEE, 4-11
OPER?, 4-11
PRINt, 4-12
RECall SETup, 4-12
RUN, 4-12
SERial, 4-13
SINGle, 4-13
STOP, 4-13
STORe SETup, 4-13
STORe WAVEform, 4-14
TER?, 4-14
UEE, 4-14
UER?, 4-14
VIEW, 4-15
RPANnotation, 16-3
RQC (Request Control), 1-18
bit, 3-4
RQS (Request Service), 1-18
and *STB, 3-13
default, 1-34
RQS/MSS bit, 3-13
RRATe, 11-7
*RST (Reset), 3-7
RUN, 4-12
and GET relationship, 1-35
RUNTil, 6-4, 15-4, 17-7
S
sample rate, number of points, 6-3
SAMPlers, 7-9
SAMPles?, 17-5
saturation, 11-8
*SAV (Save), 3-11
SAVE, 17-7
save/recall register, 3-7, 3-11
SCALe, 8-6
DEFault, 17-7
MODE, 17-8
SIZE, 14-3
SOURce?, 17-8
X1, 17-8
XDELta, 17-9
Y1, 17-9
Y2, 17-9
SCALe?, 18-26
SCOLor, 11-7
SCPI (standard commands for program-
mable instruments)
standard, 1-2
screen captures, 10-7
SCReen HARDcopy AREA, 6-5, 15-7,
17-11
SDONe?, 7-9
selected device clear (SDC), 1-35
self test, 3-14
semicolon, 1-23
SENDvalid, 18-40
sequential and overlapped commands,
1-25

Agilent Technologies 86100A Specifications

General

Brand	Agilent Technologies
Model	86100A
Category	Test Equipment
Language	English