Index
Service Guide N5242-90001 Index-9
front panel keypad assembly
removal and replacement
illustrated
, 7-11
troubleshooting, 4-13
front panel LED board
illustrated, 6-19, 6-41, 6-47,
6-59
functional groups
, 5-4
fuses
, 6-82
G
gain, IF
adjustment, 3-37
general safety considerations
, 1-3
GPIB
, 8-9
cables
part numbers
, 6-82
port
rear panel connector
, 5-33
GPIB board
illustrated, 6-15
part number, 6-14
removal and replacement
illustrated
, 7-25
procedure, 7-24
GPIB CONTROLLER
port
running test software
, 4-17
troubleshooting, 4-17
systems check
, 4-17
ground, safety earth
, 1-3
groups
functional, 5-4
H
H08, pulsed RF measurements
,
2-3
handle
damaged, 1-3
kits
part numbers
, 6-83
HANDLER I/O
connector
pin assignments
, 5-14
rear panel
, 5-12
hard disk drive
copying files from, 7-48
data storage
, 5-33
installing backup files onto
, 7-51
operation
, 5-33
removal and replacement
illustrated
, 7-49
procedure, 7-48
unique files located on
, 7-48
hardware
in bottom assembly
illustrated, 6-73
part numbers, 6-72
in external analyzer
illustrated
, 6-79
part numbers
, 6-78
in internal analyzer
illustrated
, 6-77
part numbers
, 6-76
in rear panel assembly
illustrated
, 6-81
part numbers
, 6-80
in top assembly
illustrated
, 6-70, 6-71
part numbers
, 6-70
location of part numbers
, 6-9
options
, 2-3, 8-14
hardware, Option 029
in bottom assembly
illustrated
, 6-75
part numbers, 6-74
high dynamic range
measurement configuration,
5-17
HMA26.5
illustrated, 6-19, 6-25, 6-33,
6-41, 6-47, 6-59
operation
, 5-11, 5-17
part number, 6-18, 6-24, 6-32,
6-40, 6-46, 6-58
removal and replacement
illustrated
, 7-31
procedure
, 7-30
troubleshooting
, 4-30
I
IDE
data storage, 5-33
IF gain
adjustment, 3-37
IF inputs, Option 020
, 2-4
IF multiplexer board
illustrated, 6-19, 6-25, 6-33,
6-41, 6-47, 6-59
operation
, 5-22
part number
, 6-18, 6-24, 6-32,
6-40, 6-46, 6-58
removal and replacement
illustrated
, 7-29
procedure
, 7-28
troubleshooting
, 4-39
insertion loss
check
failure of, 3-14
test port cables
, 3-14
installing
a serial number, 8-16
instruction documentation
symbol
, 1-7
instrument markings
, 1-7
instrument specifications
, 3-6
interconnects
front panel, 5-31
HANDLER I/O
pin assignments
, 5-14
PULSE I/O
pin assignments
, 5-23
PWR I/O
pin assignments
, 5-15
rear panel
, 5-11, 5-12, 5-22,
5-33
Display
, 5-33
EXT 10 MHz REF IN
, 5-11
EXT 10 MHz REF OUT
, 5-11
GPIB
, 5-33
HANDLER I/O
, 5-12
LAN, 5-33
TEST SET I/O
, 5-12
USB
, 5-33
VGA, 5-33
TEST SET I/O
pin assignments
, 5-13
internal analyzer
replaceable hardware
illustrated
, 6-77
part numbers
, 6-76
replaceable parts
illustrated
, 6-77
part numbers
, 6-76
internal performance test
software
, 3-28
inverter board
illustrated, 6-13
part number
, 6-12
removal and replacement
illustrated
, 7-11
procedure
, 7-10
troubleshooting
, 4-12
IP address, LAN
, 4-19
ISM1-A mark
, 1-7
ISO 17025 standards compliant
calibration, Option 1A7
, 2-7
isolation
cause of failure, 8-12
definition of
, 8-12
measurements affected by
, 8-12
K
keypad assembly
illustrated, 6-13
operation
, 5-31
parts list
, 6-12
removal and replacement
illustrated
, 7-11
procedure
, 7-10
test, 4-14
troubleshooting
, 4-13
To Next Page
Loading...
