Index
Service Guide N5242-90001 Index-13
illustrated, 6-19, 6-41, 6-47,
6-59
part numbers, 6-18, 6-24,
6-25, 6-32, 6-33, 6-40,
6-46, 6-58
in external analyzer
illustrated
, 6-79
part numbers
, 6-78
in front panel assembly
illustrated
, 6-11, 6-13
part numbers
, 6-10, 6-12
in internal analyzer
illustrated
, 6-77
part numbers
, 6-76
in rear panel assembly
illustrated
, 6-81
part numbers
, 6-80
in top assembly, all options
illustrated
, 6-70, 6-71
part numbers
, 6-14, 6-15, 6-70
locating
by reference designator
, 6-5
by type of part
, 6-7
miscellaneous
part numbers
, 6-82
required for servicing
, 2-12
replaceable
listing of
, 6-5
ordering information
, 6-3
parts, hardware
in bottom assembly
illustrated
, 6-73
part numbers
, 6-72
in external analyzer, all options
illustrated
, 6-79
part numbers
, 6-78
in internal analyzer, all options
illustrated
, 6-77
part numbers
, 6-76
in rear panel assembly, all
options
illustrated
, 6-81
part numbers
, 6-80
in top assembly, all options
illustrated
, 6-70, 6-71
part numbers
, 6-70
parts, Option 029
in bottom assembly
illustrated
, 6-75
part numbers
, 6-74
parts, Option 029 hardware
in bottom assembly
illustrated
, 6-75
part numbers, 6-74
password
Agilent administrator, 7-50
performance
tests, 3-28
calibration coefficients
, 3-33
description of
, 3-7
dynamic accuracy, 3-34
frequency accuracy
, 3-30
noise floor
, 3-32
receiver compression, 3-31
source maximum power
output
, 3-29
source power accuracy, 3-28
source power linearity
, 3-29
test port output maximum
power
, 3-29
test port output power
accuracy
, 3-28
test port output power
linearity
, 3-29
trace noise
, 3-30
verification
ANSI/NCSL Z540-1-1994
, 3-8
non-ANSI/NCSL Z540-1-1994
,
3-9
performance test software,
internal
, 3-28
phase stability check
failure of, 3-16
test port cables
, 3-15
pin assignments
connectors
HANDLER I/O
, 5-14
PULSE I/O
, 5-23
PWR I/O, 5-15
TEST SET I/O
, 5-13
ping
command, LAN, 4-19
from network, 4-20
to analyzer
, 4-19
pixel
damaged, 4-15
definition
, 4-15
Port 1
typical power output, 4-34
Port 2
typical power output, 4-34
Port 3
typical power output, 4-34
Port 4
typical power output, 4-34
post-repair procedures
, 7-64
power button keypad
removal and replacement
illustrated
, 7-11
procedure
, 7-11
power supply
check, 4-7
functional description of, 5-6
functional group
, 5-4
operation
, 5-34
power supply assembly
illustrated, 6-15
part number
, 6-14
removal and replacement
illustrated
, 7-21
procedure
, 7-20
troubleshooting
, 4-7
power switch board
illustrated, 6-13
parts list
, 6-12
removal and replacement
illustrated
, 7-11
procedure
, 7-11
power switch overlay
part number, 6-10, 6-11
power up
troubleshooting, 4-6
power, source
accuracy test, 3-28
linearity test
, 3-29
power, source output
maximum test, 3-29
power, test port output
accuracy test, 3-28
linearity test
, 3-29
maximum test, 3-29
pre-repair
procedures
caution about
, 7-3
warnings about, 7-3
preventive maintenance
effect on error terms, 8-3
procedure
, 7-14
processing subgroup
operation, 5-32
protection
against ESD, 1-6, 3-4, 4-3, 7-3,
8-4
pulse generators-internal,
Option 025
, 2-4
PULSE I/O
connector
pin assignments
, 5-23
pulse I/O adapter, accessory
, 2-9
pulse modulator-source 1,
Option 021
, 2-4
pulse modulator-source 2,
Option 022
, 2-4
pulsed RF measurements,
Option H08
, 2-3
PWR I/O
connector
pin assignments
, 5-15
R
R channel
troubleshooting, 4-25
R trace
troubleshooting, 4-25, 4-28
rack mount kits
part numbers, 6-83
To Next Page
Loading...
