Akai QZ-503R Series

Before operating
SIS
SSS
SSS
Power on/off
Although
the
system's
power
will
be
turned
on
when
the
(
/
|
button
is
pressed,
the
system
will
take
5
seconds
to
stabi-
lize
itself.
During
this
time,
the
power
indicator
will
flash
and
operation
buttons
will
not
be
operable.
Pressing
the
/
I
button
again
will
turn
the
power
off.
Even
when
the
power
is
off,
power
is
still
being
supplied
to
some
of
the
system’s
circuits,
such
as
the
time
circuit.
For
safety,
unplug
the
power
cord
from
your
household
AC
power
outlet
when
you
will
not
be
using
this unit
for
a
long
period
of
time.
Power save mode
When the power save mode is engaged, in order to con-
serve energy the system will be turned off when CD, MD or
TAPE
input
is
selected
and
the
component
has
not
been
used for more than 10 minutes.
i To engage the power save mode:
When the system's power is turned on, press the remote
control's ) /1 button for more than 2 seconds. “POWER S”
will
appear
on
the
FL
display,
indicating
that
the
power
save mode is engaged.
When
the
power
save
mode
is
engaged,
“P”
will
appear
on
the
FL
display
when
the
system's
power
is
turned
off.
Mi To cancel the power save mode:
When
turning
off
the
power,
press
the
/
I
button
on
the
remote
control
until
the
“P”
indicator
goes
out.
About the JOG dial:
SET The JOG dial includes a power
ey save circuit to prevent wear of
remote control batteries. When
the JOG dial is not used for
more than 3 minutes, the |
power save mode is engaged,
aoe disabling the JOG dial. To use
the
JOG
dial
in
this
case,
first
press
the
SET/JOG
button
before using.
Setting the clock
This
system
has
a
built-in
clock
circuit.
Before
the
timer-con-
trolled
functions
can
be
used,
the
clock
must
be
set
to
the
current
time.
The
clock
will
function
even
while
the
system's
power
is
off.
The
current
time
will
be
displayed
on
the
FL
display.
| Ge. pce || I TIMER
=
EGS
JOG
| Press the TIMER button.
“SLEEP” will appear on the FL display.
2 Turn the JOG dial to select “CLOCK”.
The
FL
display
will
change
in
the
following
order
when
the JOG dial is turned.
[SLEEP] <> Wake]
(GLOCK] «> CREC }
3 Press the SET button.
The time will be displayed.
Hour Minutes
Input the current time
e Turn the JOG dial to input the flashing hour and press
the SET button.
© Turn the JOG dial to input the flashing minutes.
4
Press
the
SET
button
to
set
the
current
time.
The
input
source
display
will
appear
after
3
seconds.
Note:
®
The
timer
employs
a
24
hour
clock.
0:00
indicates
mid-
night
and
12:00
indicates
noon.
©
Ifa
power
failure
occurs,
or
if
the
power
cord
is
unplugged,
the
power
backup
mode
will
function
providing
power
backup
for
approx.
1
minute.
Data
will
be
retained
during
this
time.
If
the
power
is
off
for
more
than
1
minute,
please
reset
the
clock
data.