WLAN Gateway
Page 104 7750 SR RADIUS Attributes Reference Guide
26-6527-188 Alc-Wlan-Dsm-
Ingress-Policer
Specifies the name of a distributed subscriber management (DSM) ingress
policer configured under configure subscriber-mgmt wlan-gw distributed-
sub-mgmt dsm-policer <policer-name>. This policer will be applied to the
DSM UE. This overrides the value configured under configure service ies/
vprn <svc-id> subscriber-interface <subscriber-interface-name> group-
interface <group-interface-name> wlan-gw vlan-tag-ranges range start
<starting-vlan> end <ending-vlan> distributed-sub-mgmt ingress-policer.
26-6527-189 Alc-Wlan-Dsm-Egress-
Policer
Specifies the name of a distributed subscriber management (DSM) egress
policer configured under configure subscriber-mgmt wlan-gw distributed-
sub-mgmt dsm-policer <policer-name>. This policer will be applied to the
DSM UE. This overrides the value configured under configure service ies/
vprn <svc-id> subscriber-interface <subscriber-interface-name> group-
interface <group-interface-name> wlan-gw vlan-tag-ranges range start
<starting-vlan> end <ending-vlan> distributed-sub-mgmt egress-policer.
26-6527-190 Alc-Wlan-Handover-
Ip-Address
IP address provided in RADIUS Access-Accept message to signal handover
from LTE or UMTS to WIFI. If this VSA is present, handover indication is set
in GTP session creation request to PGW/GGSN.
26-6527-205 Alc-GTP-Default-
Bearer-Id
When establishing a GTP connection for a UE, this specifies the bearer id
(GTPv2) or NSAPI (GTPv1) that will be used for the data path connection. If
not provided, a default value of 5 will be used.
26-6527-206 Alc-Wlan-SSID-VLAN The VLAN is transparently taken from the UE’s Ethernet layer and can be
reflected in both authentication and accounting. This is typically added by the
Access Point and uniquely identifies an SSID. This is useful when the SSID is
not available in the called-station-id (e.g., datatrigger scenarios). When this
attribute is configured for inclusion but no vlan is present in the UE payload,
the attribute will not be reflected in RADIUS.
26-6527-216 Alc-Datatrig-Lease-
Time
Defines the initial lease-time used for data-triggered DHCP relay hosts. If this
attribute is not provided or equal to zero, the used lease-time will be 7 days.
This lease time will be overridden upon the first renew after data-triggered
host-creation.
26-25053-2 Ruckus-Sta-RSSI Received Signal Strength Indication. Used in conjunction with the radius-
proxy track-accounting feature. When the radius-proxy receives this attribute
in an accounting message, it will be copied into the DHCP lease state and
echoed by the SROS accounting.
26-10415-1 3GPP-IMSI This is used to identify the host in a GTP-C connection. If not present and a
gtp-c connection is requested, the subscriber-id or username in the EAP-SIM
message will be parsed as an IMSI. This should be provided for any GTP-C
user.
26-10415-5 3GPP-GPRS-
Negotiated-QoS-Profile
Used to signal the QOS for default bearer or primary PDP context via GTP
“QOS IE” in create-PDP-context and "Bearer QOS" in create-session-request
Table 28: WLAN Gateway (description) (Continued)
Attribute ID Attribute Name Description
To Next Page
Loading...
