VIPEDIA-12 Products – Installation Guide
U-0641-0344.docx – Issue: 8 complete, approved
Page 3 of 52
Document Change History
Issue Amendment Summary Date
1 Draft release for internal use 01/03/11
2 Draft release for internal use 02/03/11
3 First release 10/12/12
4 1) "Batteries shall not be exposed to excessive heat such as sunshine, fire etc" warning added
for EN 60065.
2) DBB max cable run added (1 m).
3) Max dimensions for RJ45 connector added.
4) Current consumption updated.
27/02/13
5 1) Document part number (M0641_27) added to the bottom of the front cover.
2) BOA Contact Inputs note corrected: contacts are configurable as digital or analogue in
groups of 4 (port) not in groups of six.
3) DVA format added to the Technical Specification.
4) Expansion port label updated from “EXPAND” to “DBB” per new silkscreen.
5) AUDIO INPUTS: fire microphone with hardwired PTT should not be powered from Vipedia.
6) BOA diagram shows EMC gasket fitment.
7) Current consumption updated.
05/12/13
6 1) DBB: max cable run corrected from 1 m to 4 m.
2) Accreditation logos/number removed from the back of the front page (as they may change
on recertification).
3) BOA02 connections details added.
4) EMS/MPS connection diagrams added.
5) Current consumption updated.
6) Typos corrected, some paragraphs re-worded and additional info added for clarity.
29/08/14
7 1) Template updated.
2) Technical Specification updated:
a) Phantom power voltage added (48 V).
b) Digital contact input voltage range and 100 kohms resistor to ground added.
c) Contact outputs: max voltage & current per output and supply max current added.
d) DVAs: 12 kHz and 24 kHz sample rate added.
e) IP rating corrected: from IP30 to IP20.
f) On-board analogue contact input voltage range added for non-monitored and monitored
inputs.
g) Baud rate added to serial ports.
h) Optional Modules updated.
i) Changeover relays updated for include use with RCB01.
j) Hard Clipper and Surveillance Tone: both available as standard since V1.9 (footnote
removed).
k) ANS Minimum Threshold / ANS Maximum Threshold updated from 50 dBA / 90 dBA to
55dBA / 95 dBA.
3) Network Card USB port added to connector description.
4) Connection diagram for EAP01 added.
5) Crosstalk corrected: from “>70 dB at 1 kHz” to “> 70 dB below full output at 1 kHz”
6) Rear panel RJ45 description corrected from “jack” to “socket”.
7) AMP CTRL connector pinout updated: from ACAN DXP/DXN to DXP/DXN.
8) BOA01 and BOA02: T568B colour added to RJ45 pin numbering.
9) CE statement updated to new format.
10) ETH3 and ETH4 description: from 1000BASE-T to 100BASE-T.
11) AUDIO INPUTS: note on power supply removed as power supply always enabled
irrespective of microphone configuration (since V2.1).
12) Relay 2 description updated to include user with RCB01.
13) Safety and Precautions updated mostly for CB compliance, for example (see document for
full details):
a) Restricted access location.
b) No copper connections between peripherals and the INTEGRA between buildings.
Fibre interconnection is acceptable.
c) Lithium battery temperature rating to be greater than 75 °C.
d) Battery replacement/disposal warnings.
17/05/19
To Next Page
Loading...
Need help?
General