Need help?Do you have a question about the Axia xNode and is the answer not in the manual?
General| Brand | Axia |
|---|---|
| Model | xNode |
| Category | Media Converter |
| Language | English |
General safety precautions for installation, servicing, electrical hazards, and voltage.
Warnings about ventilation, moisture, and proper usage to prevent damage or fire hazards.
USA, Canada, and CE compliance statements and directives.
Lists trademarks and disclaimer regarding third-party products.
Details the product warranty and information on software updates.
Instructions for providing feedback and obtaining factory service.
Provides phone, email, and web contact details for technical support.
Information on registering the product for warranty activation online.
Describes the different xNode models and their general features.
Details the OLED display for setup and status information.
Overview of IEC connector, Ethernet ports, and mounting options.
Introduces Analog, AES/EBU, Microphone, and Mixed Signal xNodes.
Details the GPIO ports and their opto-isolated inputs/outputs.
Explains access to the web interface for setup and maintenance.
Information displayed on the Home page: ID, version, temp, network status.
Step-by-step guide for initial xNode configuration using the front panel.
Steps to manually assign an IP address via front panel or web interface.
Using the web interface for configuring sources and destinations.
Configuring device host name and network address.
Detailed steps for assigning a unique ID and IP address.
Using iProbe for device discovery and initial configuration via bootp.
Procedure to reset the xNode to its original factory settings.
Details on the optional surface mount kit for installation.
Instructions for installing the optional rack mount kit.
Procedures for mounting single and double xNode units in a rack.
Configuration settings for network, logging, authentication, and firmware.
Details advanced options for audio xNodes, including System and Host Name.
Configuration for Livewire clocking, priority, and synchronization modes.
Settings for Precision Time Protocol domain, delay, and priority.
Real-time audio level metering with gain adjustment features.
Introduction to the matrix mixer for routing audio signals.
Setting up output names, channels, types, and gain for audio destinations.
Configuring input names, channel numbers, and stream modes for audio sources.
Setting up multichannel audio links using RTSP.
Details the RJ45 and DB-25 connectors for analog audio I/O.
Pin assignments for analog line input/output RJ45 ports.
Pin assignments for the analog audio I/O DB-25 connector.
Details the RJ45 and DB-25 connectors for AES/EBU audio I/O.
Pin assignments for AES/EBU input/output RJ45 ports.
Pin assignments for the AES/EBU audio I/O DB-25 connector.
Details RJ45 and DB-25 connectors for microphone inputs and analog outputs.
Pin assignments for microphone mono inputs and analog outputs.
Pin assignments for the microphone inputs DB-25 connector.
Pin assignments for the analog line outputs DB-25 connector.
Details the DA-15 ports for GPIO functionality.
Explains pin configuration for GPI, GPO, power, and ground.
Information on external power supply limits and current limiting resistors.
How accessory modules interface directly with GPIO ports.
Basic configuration for GPIO ports (name, channel, status).
Explains port routing, channel assignment, and Pathfinder control.
Overview of Home and System pages for GPIO xNode configuration.
Details RJ45 connectors for audio and XLR for mic input.
Pin assignments for mixed signal inputs and outputs.
Pin assignments for the XLR microphone input.
Information on external power supply limits and current limiting resistors for GPIO.
Configuration for the two GPIO ports on the Mixed Signal xNode.
Logic table for operator microphone inputs and outputs.
Logic table for guest microphone inputs and outputs.
Logic table for producer microphone inputs and outputs.
Logic table for line input signals and their control.
Logic table for codec inputs and outputs.
Logic table for telephone hybrid interface control.
Logic table for control room monitor control.
Logic table for computer playback device control.
Technical specifications for microphone preamplifiers.
Technical specifications for analog line inputs.
Technical specifications for analog line outputs.
Technical specifications for digital audio inputs and outputs.
Specs for dynamic range, THD+N, crosstalk, CMRR, and noise.
Specs for power supply, operating temp, and physical dimensions.
Introduction to the AES67 standard for audio over networks.
Configuration for PTP clock synchronization and modes.
Setup for transmitting and receiving multicast audio streams.
Configuring destinations for receiving multicast streams.
Setup for unicast audio streaming using SIP URIs.
Details the five-year limited warranty and voiding conditions.
Steps to invoke the warranty and contact Telos for service.
Information on shipping costs for warranty claims and evaluation fees.
To Next Page