Azbil SDC36 User Manual

9-3
Chapter 9. LIST OF COMMUNICATION DATA
Bank Item name
RAM address EEPROM address RAM EEPROM
Decimal
point
information
Notes
Decimal Hexadecimal Decimal Hexadecimal Read Write Read Write
Setup Auxiliary output scaling low limit 5254 1486 21638 5486 S
Auxiliary output scaling high limit 5255 1487 21639 5487 S
Auxiliary output MV scalable
bandwidth
5256 1488 21640 5488 P
(Note 2)
Position proportional type
5257 1489 21641 5489
* *
—
Position proportional control dead zone 5258 148A 21642 548A
* *
1
Motor long life mode 5259 148B 21643 548B
* *
—
Motor adjust 5260 148C 21644 548C
* *
—
Input with motor fully closed 5261 148D 21645 548D
* *
—
Input with motor fully open 5262 148E 21646 548E
* *
—
Motor full close-full open time 5263 148F 21647 548F
* *
1
Communication type 5264 1490 21648 5490 X X —
Station address 5265 1491 21649 5491 X X —
Transmission speed 5266 1492 21650 5492 X X —
Data format (Data length) 5267 1493 21651 5493 X X —
Data format (Parity) 5268 1494 21652 5494 X X —
Data format (Stop bit) 5269 1495 21653 5495 X X —
Communication minimum response
time
5270 1496 21654 5496 X X —
Key operation type 5271 1497 21655 5497 —
[mode] key function 5272 1498 21656 5498 —
MODE display setup 5273 1499 21657 5499 —
PV/SP display setup 5274 149A 21658 549A —
MV display setup 5275 149B 21659 549B —
Event setting value display setup 5276 149C 21660 549C —
Event remaining time display setup 5277 149D 21661 549D —
CT input current value display setup 5278 149E 21662 549E —
User level 5279 149F 21663 549F —
LED monitor 5280 14A0 21664 54A0 —
MS indicating lamp ON condition
(1st priority)
5281 14A1 21665 54A1 —
MS indicating lamp ON status
(1st priority)
5282 14A2 21666 54A2 —
MS indicating lamp ON condition
(2nd priority)
5283 14A3 21667 54A3 —
MS indicating lamp ON status
(2nd priority)
5284 14A4 21668 54A4 —
MS indicating lamp ON condition
(3rd priority)
5285 14A5 21669 54A5 —
MS indicating lamp ON status
(3rd priority)
5286 14A6 21670 54A6 —
MS indicating lamp deviation range 5287 14A7 21671 54A7 —
Special function 5288 14A8 21672 54A8 X —
Zener barrier adjustment 5289 14A9 21673 54A9 X X —
CT1 turns 5290 14AA 21674 54AA — (Note 2)
Number of CT1 power wire loops
5291 14AB 21675 54AB — (Note 2)
CT2 turns
5292 14AC 21676 54AC — (Note 2)
Number of CT2 power wire loops
5293 14AD 21677 54AD — (Note 2)
PV input failure (under range) type
5297 14B1 21681 54B1 — (Note 1)
DI
Assignment
Internal Contact 1 Operation type 5401 1519 21785 5519 —
Internal Contact 1 Input bit operation 5402 151A 21786 551A —
Internal Contact 1 Input assignment A 5403 151B 21787 551B —
Internal Contact 1 Input assignment B 5404 151C 21788 551C —
Internal Contact 1 Input assignment C 5405 151D 21789 551D —
Internal Contact 1 Input assignment D 5406 151E 21790 551E —
(Continue on next page.)
(Note 1) If ROM version 1 in the instrument information bank (
I

d02
) is 2.26 or earlier,
write accessibility is X and read accessibility is ∆.
(Note 2) If ROM version 1 in the instrument information bank (
I

d02
) is 2.04 or earlier, this item is reserved for
future extension, write accessibility is X and read accessibility is ∆ for both RAM and EEPROM.

Azbil SDC36 Specifications

General

Brand	Azbil
Model	SDC36
Category	Controller
Language	English