EasyManuals Logo

B&R 8LS 3 Series User Manual

B&R 8LS 3 Series
300 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #214 background imageLoading...
Page #214 background image
Technical data
214 8LS...-3 user's manual V2.50
Model number 8LSC74.ee030ffgg-3 8LSC74.ee045ffgg-3 8LSC75.ee022ffgg-3 8LSC75.ee030ffgg-0
Motor
Nominal speed n
N
[rpm] 3000 4500 2200 3000
Number of pole pairs 5 3
Nominal torque M
n
[Nm] 34 24.6 45.5 39
Nominal power P
N
[W] 10681 11592 10482 12252
Nominal current I
N
[A] 20.86 22.57 20.5 23.93
Stall torque M
0
[Nm] 43 56 48
Stall current I
0
[A] 26.38 39.45 25.2 29.4
Maximum torque M
max
[Nm] 150 187
Maximum current I
max
[A] 135.33 202 124 176
Maximum speed n
max
[rpm] 6000 4500
Torque constant K
T
[Nm/A] 1.63 1.09 2.22 1.63
Voltage constant K
E
[V/1000 rpm] 98.44 65.97 134.04 98.4
Stator resistance R
2ph
[Ω] 0.28 0.13 0.39 0.21
Stator inductance L
2ph
[mH] 4.9 2.2 7.1 3.07
Electrical time constant t
el
[ms] 17.5 16.92 17.5 14.62
Thermal time constant t
therm
[min] 41 46 65
Moment of inertia J [kgcm
2
] 60 74 154.7
Weight without brake m [kg] 24 28 38
Holding brake
Holding torque of brake M
Br
[Nm] 47 32
Mass of brake [kg] 0 1.6
Moment of inertia of brake J
Br
[kgcm
2
] 32 5.85
Recommendations
ACOPOS 8Vxxxx.xx... 1320 1640 1320
ACOPOSmulti 8BVIxxxx... 0330 0440 0330
ACOPOS P3 8EIxxxx... 034X 044X 034X -
Cross section for B&R motor cables
[mm
2
]
4 10 4
Connector size 1.0 1.5 1.0
NOTE about servo drives: The recommended servo drive / inverter module is designed for 1.1x the stall current. If more than double the amount is needed during
the acceleration phase, the next larger servo drive should be selected. This recommendation is only a guideline; detailed inspection of the corresponding speed/
torque characteristic curve can result in deviations of the servo drive size (larger or smaller).
NOTE about cable cross section: The B&R motor cables with this cable cross section are produced optimally (cables stripped to the correct length) for the
ACOPOS servo drive or the recommended ACOPOS inverter module. B&R motor cables with other cable cross sections can also be used (within the specified
terminal cross section range) and can be obtained from B&R in the desired design on request. Note the type of wiring.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the B&R 8LS 3 Series and is the answer not in the manual?

B&R 8LS 3 Series Specifications

General IconGeneral
BrandB&R
Model8LS 3 Series
CategoryEngine
LanguageEnglish