page 14page 14
page 14page 14
page 14
930/937 Mulcher (O)
800-00256
WARNING WARNING
WARNING WARNING
WARNING
Do not exceed 15 p.s.i. nozzle pressure whenDo not exceed 15 p.s.i. nozzle pressure when
Do not exceed 15 p.s.i. nozzle pressure whenDo not exceed 15 p.s.i. nozzle pressure when
Do not exceed 15 p.s.i. nozzle pressure when
drying parts with compressed air. Do not directdrying parts with compressed air. Do not direct
drying parts with compressed air. Do not directdrying parts with compressed air. Do not direct
drying parts with compressed air. Do not direct
compressed air against human skin. Seriouscompressed air against human skin. Serious
compressed air against human skin. Seriouscompressed air against human skin. Serious
compressed air against human skin. Serious
injury could result.injury could result.
injury could result.injury could result.
injury could result.
CALIFORNIACALIFORNIA
CALIFORNIACALIFORNIA
CALIFORNIA
Proposition 65 WarningProposition 65 Warning
Proposition 65 WarningProposition 65 Warning
Proposition 65 Warning
Diesel engine exhaust and some of its constituents areDiesel engine exhaust and some of its constituents are
Diesel engine exhaust and some of its constituents areDiesel engine exhaust and some of its constituents are
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birthknown to the State of California to cause cancer, birth
known to the State of California to cause cancer, birthknown to the State of California to cause cancer, birth
known to the State of California to cause cancer, birth
defects, and other reproductive harm.defects, and other reproductive harm.
defects, and other reproductive harm.defects, and other reproductive harm.
defects, and other reproductive harm.
WARNING WARNING
WARNING WARNING
WARNING
If this machine is equipped with electric motorIf this machine is equipped with electric motor
If this machine is equipped with electric motorIf this machine is equipped with electric motor
If this machine is equipped with electric motor
driven Auxiliary Oil Cooler & Hydraulic Drivindriven Auxiliary Oil Cooler & Hydraulic Drivin
driven Auxiliary Oil Cooler & Hydraulic Drivindriven Auxiliary Oil Cooler & Hydraulic Drivin
driven Auxiliary Oil Cooler & Hydraulic Drivin
Fans, be sure battery is disconnected beforeFans, be sure battery is disconnected before
Fans, be sure battery is disconnected beforeFans, be sure battery is disconnected before
Fans, be sure battery is disconnected before
going near cooler fan. If battery is notgoing near cooler fan. If battery is not
going near cooler fan. If battery is notgoing near cooler fan. If battery is not
going near cooler fan. If battery is not
disconnected, fan may come on at any timedisconnected, fan may come on at any time
disconnected, fan may come on at any timedisconnected, fan may come on at any time
disconnected, fan may come on at any time
causing severe injury.causing severe injury.
causing severe injury.causing severe injury.
causing severe injury.
SAFETY SUMMARY CONTINUED...
When you work on slopes there are several important points to consider:
Always use a seat belt when provided.
Speed of travel or working tools – higher speeds or sudden starts and stops can tend to make the machine
less stable
Terrain – soft ground, slopes, uneven surfaces (stumps, fallen trees and slash, rocks, valleys/rises, drop-offs or
ledges, overhangs), changing soil types, moisture, ice and snow affect the machine stability. Irregular terrain
must be traveled at slower speeds.
Direction of travel - Avoid operating the machine across the slope. When possible travel up or down slopes.
Place the heaviest end of the machine uphill and keep the load low to the ground. Turning uphill with an
articulated machine can increase the chance of tip-over.
Loads and shifting loads – Do not overload. Keep the load low and close to the machine. Contact with
overhead wires, trees, fallen trees or the ground can cause the load to shift unexpectedly and reduce stability.
Machine configuration – Will affect the weight distribution, the stability, the operating performance, and the
machine control on slopes.
Visibility – irregular, snow-covered or slash-covered terrain can reduce visibility in the path of the tracks or
wheels and to the surrounding area, the load, other vehicles, obstacles, and people.
Condition of the machine – Machine control and performance when operating on slopes may require special
machine maintenance or more frequent intervals. Fluid levels, track tension or tire inflation pressure can affect
machine control on slopes.
Do not operate a machine on a slope without proper training. Learn the stability limits of the machine by first
working on gentle slopes. Gain experience and improve skills over time by gradually increasing the angle of
slopes on which you are working. As operating conditions change make the appropriate decisions and
adjustments to maintain safe machine operation.
SAFE OPERATION ON SLOPED TERRAINSAFE OPERATION ON SLOPED TERRAIN
SAFE OPERATION ON SLOPED TERRAINSAFE OPERATION ON SLOPED TERRAIN
SAFE OPERATION ON SLOPED TERRAIN
To Next Page
