Barko Hydraulics 930 - Machine Control Switches and Levers

page 20page 20
page 20page 20
page 20
930/937 Mulcher (O)
800-00256
CONTROL FUNCTIONS CONTINUED...
Figure 3Figure 3
Figure 3Figure 3
Figure 3
Figure 2Figure 2
Figure 2Figure 2
Figure 2
Forward forForward for
Forward forForward for
Forward for
High GearHigh Gear
High GearHigh Gear
High Gear
Back forBack for
Back forBack for
Back for
Low GearLow Gear
Low GearLow Gear
Low Gear
Straight UpStraight Up
Straight UpStraight Up
Straight Up
for Neutralfor Neutral
for Neutralfor Neutral
for Neutral
Push to ApplyPush to Apply
Push to ApplyPush to Apply
Push to Apply
BrakeBrake
BrakeBrake
Brake
THROTTLE KNOBTHROTTLE KNOB
THROTTLE KNOBTHROTTLE KNOB
THROTTLE KNOB
(See Figure 1)
Turn Clockwise to increase the RPM of the engine.
Turn Counter Clockwise to decrease the RPM of the
engine. Push the dial in for idle.
EMERGENCY BRAKE PEDALEMERGENCY BRAKE PEDAL
EMERGENCY BRAKE PEDALEMERGENCY BRAKE PEDAL
EMERGENCY BRAKE PEDAL
(See Figure 2)
Depress foot pedal to apply brake.
Release foot pressure on pedal to release brake.
CAUTION CAUTION
CAUTION CAUTION
CAUTION
The emergency brake foot pedal is forThe emergency brake foot pedal is for
The emergency brake foot pedal is forThe emergency brake foot pedal is for
The emergency brake foot pedal is for
emergency use only! Using it for purposesemergency use only! Using it for purposes
emergency use only! Using it for purposesemergency use only! Using it for purposes
emergency use only! Using it for purposes
other than an emergency could result in overother than an emergency could result in over
other than an emergency could result in overother than an emergency could result in over
other than an emergency could result in over
heating of brake disc and loss of brakingheating of brake disc and loss of braking
heating of brake disc and loss of brakingheating of brake disc and loss of braking
heating of brake disc and loss of braking
power.power.
power.power.
power.
GEAR SHIFT LEVERGEAR SHIFT LEVER
GEAR SHIFT LEVERGEAR SHIFT LEVER
GEAR SHIFT LEVER
(See Figure 3)
Push lever forward for high gear, position lever
straight up for neutral, and pull lever backward for low
gear.
Move this lever only while machine isMove this lever only while machine is
Move this lever only while machine isMove this lever only while machine is
Move this lever only while machine is
stopped and travel pedal is disengaged!stopped and travel pedal is disengaged!
stopped and travel pedal is disengaged!stopped and travel pedal is disengaged!
stopped and travel pedal is disengaged!
Low gear is used for mulching.
High gear is used for moving machine when
attachment is empty.
PARKING BRAKE SWITCHPARKING BRAKE SWITCH
PARKING BRAKE SWITCHPARKING BRAKE SWITCH
PARKING BRAKE SWITCH
(See Figure 1)
Push up to apply brake.
With switch up, brake is fully applied
Push switch down to release brake.
Figure 1Figure 1
Figure 1Figure 1
Figure 1
Throttle KnobThrottle Knob
Throttle KnobThrottle Knob
Throttle Knob
Push up toPush up to
Push up toPush up to
Push up to
apply Breakapply Break
apply Breakapply Break
apply Break
Push up toPush up to
Push up toPush up to
Push up to
activate Controlsactivate Controls
activate Controlsactivate Controls
activate Controls
CONTROL POWER SWITCHCONTROL POWER SWITCH
CONTROL POWER SWITCHCONTROL POWER SWITCH
CONTROL POWER SWITCH
(See Figure 1)
Push up to activate Controls.
Controls need to be reactivaed every time the
machine is started, or the servo switch in the doors
has been tripped.