Binary B-500-MTRX-230-4x4 - EDID Configuration; EDID Setup Methods Overview; How to Configure Auto EDID

B-500-MTRX-230-4x4 Installation Manual
Pg. 16
© 2013 Binary
™
8. EDIDConguration
8.1. Source Setup
8.2. Display Setup
8.3.AutoEDIDConguration
The displays used within an installation usually vary from room to room, and some may not support all resolutions
availablefromasource.Itisnecessarytomakesuresourceswillprovideavideoandaudioformatcompatiblewith
allconnecteddisplaysprogrammedtousethem.Toaccomplishthis,theB-500-MTRX-230-4X4includesbuilt-inEDID
managementforeachsourceinput.ThestoredEDIDispersource,soalldisplaylocationswillseethesameresolution
andhavethesameaudioformatwhenthatsourceisselected.
Note: Source is only able to output one video resolution and one audio format.
Note: The default EDID for each input is always 1080p with 2 channel stereo audio, since this format is accepted by
most displays with no issues.
ThefollowingsectionsexplainconguringEDIDsviatheincludedIRRemote.BeforeconguringtheEDID,besureto
refertothesourceanddisplaymanualsforavailablefeaturesandresolutionsforeachdevice.Formoreinformation
aboutusingtheincludedremote,seeSection11.1IRRemoteonpage21.
While all EDID congurations are available via the remote, the Conguration Utility can be used for faster setup.
DownloadtheCongurationUtilityandmanualontheSupportTabfortheB-500-MTRX-230-4X4atwww.SnapAV.com.
What is EDID? EDID, or Extended Display Identication Data, is a stream of information sent from a display to a source
when the two devices are connected to tell the source what video and audio formats the display can use. This prevents
sources from outputting media that won’t work with the display.
Checkeachsourceandconrmthattheaudioformatandvideoresolutionaresetsothattheywillchangebasedonthe
EDID.Normallythissettingiscalled“Auto”orsimilar.
Note: EDID setup is not required if the source supports setting one xed video resolution and audio format.
ItisrecommendedthatConsumerElectronicsControl(CEC)beturnedOFFinalldisplayswhenusingtheB-500-MTRX-
230-4X4.Thiswillprovideforpropercommunicationofvideo/audiosignalsandallowEDIDstofunctionattheiroptimum
performance.Refertothedisplay’smanualforinformationonhowtoturnthisfunctionOFF.
ThequickestandeasiestmethodforcongurationistouseAutoEDID.Whenthismodeisusedthematrixswitcher
looksattheEDIDfromeachoftheconnecteddisplays.Itusesthehighestcommonvideoresolutiontocreateanew
EDIDandsavesthatEDIDinalloftheinputs.
Note: Auto EDID sets audio to 2ch stereo for all inputs regardless of the capability of the connected displays. If multi-
channel audio is desired, embedded EDIDs or Learned EDIDs will need to be used.
When to use Auto EDID
• Allsourceswillbeavailableonalldisplays.
• Asarststeptoconguration,followingupwithadvancedmethodsforparticulardisplaysanddedicatedsources.
Note: For advanced EDID conguration when using a legacy display and/or dedicated sources, use embedded EDIDs
or learning as described in the following sections.
Sets EDID Based on All Connected Displays Display Readout (Example)
1.PressDEFAULT
E-
2.PressNumberKey9
AA
3.PressENTER
A0
8.3.1.HowtoCongureAutoEDID
TosetupAutoEDIDconguration,rstmakesurethatalldisplaysarepoweredonandconnectedtothematrixswitcher.
Then,pressthefollowingremotebuttonsinthisorder.Besuretopresseachbuttonwithin10secondsoftheprevious
button-presstopreventthecommandfromresetting.