Bosch BMP581 - Table 27: List of I3 C Cccs

Bosch Sensortec"| BST-BMP581-DS004-02 44 | 74
Modifications reserved | Data subject to change
without notice Document number: BST-BMP581-DS004-02
5.7.3 Common Command Codes (CCC)
Supported I3C command control codes (CCCs) are listed in Table 24.
Table 27: List of I3C CCCs
CCC
Code
CCC Type
CCC name
Description
BMP581
Supported
0x00
Broadcast
ENEC
Enable events
Y
0x01
Broadcast
DISEC
Disable events
Y
0x02
Broadcast
ENTAS0
Enter active state 0
N
0x03
Broadcast
ENTAS1
Enter active state 1
N
0x04
Broadcast
ENTAS2
Enter active state 2
N
0x05
Broadcast
ENTAS3
Enter active state 3
N
0x06
Broadcast
RSTDAA
Reset dynamic address
Y
0x07
Broadcast
ENTDAA
Enter dynamic address assignment
Y
0x08
Broadcast
DEFSLVS
Define list of slaves
N
0x09
Broadcast
SETMWL
Set max write length
N
0x0A
Broadcast
SETMRL
Set max read length
N
0x0B
Broadcast
ENTTM
Enter test mode
N
0x20
Broadcast
ENTHDR0
Enter HDR mode 0
N
0x21
Broadcast
ENTHDR1
Enter HDR mode 1
N
0x22
Broadcast
ENTHDR2
Enter HDR mode 2
N
0x23
Broadcast
ENTHDR3
Enter HDR mode 3
N
0x24
Broadcast
ENTHDR4
Enter HDR mode 4
N
0x25
Broadcast
ENTHDR5
Enter HDR mode 5
N
0x26
Broadcast
ENTHDR6
Enter HDR mode 6
N
0x27
Broadcast
ENTHDR7
Enter HDR mode 7
N
0x28
Broadcast
SETXTIME
Exchange timing information
Y
0x80
Direct
ENEC
Enable events
Y
0x81
Direct
DISEC
Disable events
Y
0x82
Direct
ENTAS0
Enter active state 0
N
0x83
Direct
ENTAS1
Enter active state 1
N
0x84
Direct
ENTAS2
Enter active state 2
N
0x85
Direct
ENTAS3
Enter active state 3
N
0x86
Direct
RSTDAA
Reset dynamic address
Y
0x87
Direct
SETDASA
Set dynamic address from static address
a
Y
0x88
Direct
SETNEWDA
Set new dynamic address
Y
0x89
Direct
SETMWL
Set max write length
N
0x8A
Direct
SETMRL
Set max read length
N
0x8B
Direct
GETMWL
Get max write length
N
0x8C
Direct
GETMRL
Get max read length
N
0x8D
Direct
GETPID
Get provisional ID
Y
0x8E
Direct
GETBCR
Get bus characteristics register
Y
0x8F
Direct
GETDCR
Get device characteristics register
Y
0x90
Direct
GETSTATUS
Get device status
Y
0x91
Direct
GETACCMST
Get accept mastership
N
0x93
Direct
SETBRGTGT
Get bridge status
N
0x94
Direct
GETMXDS
Get max data speed
N
0x95
Direct
GETHDRCAP
Get HDR capability
Y
0x98
Direct
SETXTIME
Exchange timing information
Y
0x99
Direct
GETXTIME
Get timing information
Y
a. CCC SETDASA can be used once to assign the dynamic address. If the address shall be changed without resetting or power-cycling the device, CCC SETNEWDA must be used.