Page 4 P/N: 4998152533-02 Copyright ï›™2007 Bosch Security Systems, Inc. DS7200V2-UK Installer's Guide
Contents
Part I: Introduction..................................................................7
1.0 Documentation Conventions.....................................7
1.1 Type Styles Used..................................................7
1.2 Notes, Cautions, and Warnings............................7
1.3 Other Conventions................................................7
1.4 Scope of Document ..............................................7
2.0 Specifications............................................................8
2.1 Environmental Specifcations.................................8
2.2 Voltage Input to Control Panel..............................8
2.3 Power Outputs ......................................................8
2.4 Minimum Operating Voltage .................................8
2.5 Data Bus ..............................................................8
2.6 Keypads................................................................8
3.0 Standard Features ....................................................8
3.1 Communicator.......................................................8
3.2 Zones....................................................................8
3.3 Areas and Accounts..............................................8
3.4 Programmable Outputs.........................................8
3.5 Users.....................................................................8
3.6 Keyswitch/Exit Terminator ....................................8
3.7 Alarm Event Memory ............................................8
3.8 History Log............................................................9
3.9 Wireless (RF) Devices..........................................9
4.0 Control Panel Assembly............................................9
5.0 Listings and Approvals..............................................9
6.0 System Options.........................................................9
6.1 Arming Devices.....................................................9
6.2 Data Bus Devices .................................................9
6.3 RF Devices .........................................................10
6.4 Programming Tools.............................................10
7.0 System Batteries.....................................................10
7.1 Standby Battery ..................................................10
7.2 RAM Backup Battery...........................................10
8.0 Available Power ......................................................10
8.1 Auxiliary Power ...................................................10
8.2 Alarm Power .......................................................10
9.0 Installer Keypad Connector.....................................10
Part II: System Installation and Setup.................................11
10.0 Control Panel Installation........................................11
10.1 Electro Magnetic Interference (EMI)...................11
10.2 Enclosure Mounting............................................12
10.3 System Battery Installation .................................12
11.0 Telephone Connections..........................................13
12.0 Phone Line Fault.....................................................13
13.0 Communication Failure (Comm Fail)......................13
14.0 Arming Device Installation ......................................14
14.1 Keypad................................................................14
14.2 Keyswitch............................................................15
15.0 On-board Sensor Loop Setup.................................16
15.1 Overview.............................................................16
15.2 Tamper-wired Zone Configuration......................16
15.3 No EOL Zone Configuration................................16
15.4 Four-wire Smoke Detector Configuration ...........16
16.0 On-board Output Setup...........................................16
16.1 Overview.............................................................16
16.2 Programmable Output 1 (PO 1)..........................17
16.3 Programmable Outputs 2-4 (PO 2- PO 4) ..........17
17.0 RF3227E RF Receiver Setup .................................18
17.1 RF Receiver Addressing.....................................18
17.2 RF3227E Installation...........................................18
17.3 RF3227E Programming......................................18
17.4 RF Receiver Supervision....................................18
18.0 Off-board Sensor Loops (DX2010)......................... 18
18.1 DX2010 (DX2013/DX2014) Overview................ 18
18.2 DX2010 Installation ............................................ 18
18.3 DX2010 Wiring ................................................... 19
18.4 DX2010 Auxiliary Output Connections............... 20
18.5 DX2010 Tamper Input Connections................... 21
18.6 DX2010 Tamper-wired Configuration................. 21
18.7 DX2010 Addressing ........................................... 21
18.8 DX2010 Status LED ........................................... 22
18.9 DX2010 Supervision........................................... 22
19.0 Off-board Outputs (DX3010) .................................. 22
19.1 Overview............................................................. 22
19.2 DX3010 Configuration........................................ 22
19.3 DX3010 Relay Outputs....................................... 22
19.4 DX3013 Installation ............................................ 23
19.5 DX3010 Wiring ................................................... 24
19.6 DX3010 Address Programming.......................... 25
19.7 DX3010 Supervision........................................... 25
20.0 RS-232 Serial Interface (DX4010i/DX4010)........... 25
20.1 DX4010i/DX4010 Overview................................ 25
20.2 DX4010i/DX4010 Installation .............................25
20.3 RPS Direct Connection ...................................... 26
20.4 DX4010i/DX4010 Configuration Jumpers .......... 27
20.5 DX4010i/DX4010 Addressing............................. 27
20.6 DX4010i/DX4010 Supervision............................ 27
20.7 DX4010i/DX4010 DB9 Connector...................... 28
21.0 Network Interface Module (DX4020)...................... 28
21.1 DX4020 Overview .............................................. 28
21.2 DX4020 Addressing ........................................... 28
21.3 DX4020 Installation ............................................ 28
21.4 DX4020 Wiring ................................................... 30
21.5 DX4020 Programming........................................ 30
21.6 DX4020 Ethernet/Serial Status LEDs................. 31
21.7 DX4020 Supervision........................................... 31
22.0 Door Access Control Module (DACM).................... 31
22.1 DACM Overview................................................. 31
22.2 DACM Wiring...................................................... 31
22.3 DACM Supervision............................................. 32
23.0 System Power Up................................................... 32
24.0 System Status LED ................................................ 32
25.0 Installer Keypad...................................................... 33
26.0 Installer Mode......................................................... 33
27.0 Installer Menu......................................................... 33
27.1 Bell Test.............................................................. 33
27.2 Strobe Test......................................................... 33
27.3 Battery Test........................................................ 33
27.4 Test Report......................................................... 33
27.5 Zone Status........................................................ 34
27.6 Output Test......................................................... 34
27.7 RF Menu............................................................. 34
27.8 Always Force Arm .............................................. 36
27.9 Keypad Test ([#][9][1])........................................ 37
Part III: How to Program....................................................... 38
28.0 Keypad Programming............................................. 38
28.1 Installer Mode/Installer Menu ............................. 38
28.2 Expert/Installer Programming Modes................. 38
28.3 Parameter Addresses......................................... 38
28.4 Text Entry Addresses......................................... 40
28.5 Exit Programming Mode..................................... 40
To Next Page
Loading...
Need help?
General
