Bosch HPC 400 Installation Instructions For Contractors

Service menu
6.3.2 Priority heating circuit 1
BOSCH
In the default setting any changes in the outside
temperature have an effect after a delay of three hours at
the latest on the calculation of the weather-
compensated control.
~ To view the course of the outside temperature of the
last 2 days; open the Info > Room and outdoor
temp. > Outdoor temp. curve menu
This menu item allows the other heating circuits to be restricted via
heating circuit L If a heat requirement comes from heating circuit 1 and
others simultaneously. this setting is used to determine whether the
heat requirement forthe other heating circuits is always met Depending
on the setting. the heat requirement forthe other heating circuits is only
met if heating circuit 1 is supplied accordingly_
Priority heating circuit 1
No
Heating circuit 1 is the primary heating circuit. Heat requirements for other circuits are only handled if heating circuit
1
1 has a heat requirement. The flow temperature required for heating circuit 1 limits the flow temperature of the other
heating circuits _
Example : HK1 requires 50 'C . HK2 requires 55 "C. but receives a maximum of 50'C (in line with HK1) . HK3 requires
45'C and receives 45'C (notlimited by HK1) .
Unmixed heating circuit 1 will be forced to run when any other circuit requests heat. So heating circuit 1 might have a
higher temperature then wanted .
Table 26 Settings in the Priority heating circuit 1 menu
6.3.3 Settings for heating circuit 1 ... 4
Settings for the individual heating/cooling circuits can be made in this
menu. For example . you can set which heating system is installed for the
selected heating/cooling circuit. In addition it can be set whether a
remote control is available and which control type is used. It is also
possible to optimise the heating curves of the heating/cooling circuits.
NonCE: Risk of damaging the screed!
~ If an underfloor heating system is used. the max . flow
temperature recommended by the manufacturer of
the system should be observed.
At the module
User interface
CR10H
A heating/cooling circuit is not installed. If no heating/cooling circuit is installed. the heat source is only
used for DHW heating .
Electrical assemblies and components of the selected heating/cooling circuit are directly connected to the I
heat source (only available with heating circuit 1) .
Electrical assemblies and components of the selected heating/cooling circuit are connected to an MM 100
module.
CR 10 is installed as a remote control for the heating/cooling circuit. This allows
compensated control influenced by room temperature .
=-:--::-----,:------:--1
CR 10 is installed as a remote control for the selected heating/cooling circuit. This allows for weather -
compensated control influenced by room temperature.
~------------~------~------~----~--~----~---
ext. room temp . sensor Yes An additional room temperature sensor is installed (no CR 10lCR 10 H) . This allows for weather -
No
----II
Heating system heat circ. 1 Radiator
I i Convector heater
Circuit function
I Ctrl type h. clrc. 1
l __
r Max . flow temperature
Set heating curve
I Underfioor
Heating
I Cooling
Heating and cooling
0
Outdoor temp.
compensated
Outside temp . with low end
30 ... 75 .. . 85'C
(radiator/convector)
30 ... 48 ... 60'C
(underfloor heating system)
compensated control influenced by the room temperature .
No additional room temperature sensor is installed .
----- ----
Factory default of the heating curve according to heating type , e.g . curvature and design temperature
The selected heating/cooling circuit is only used to provide heating in the corresponding room .
The selected heating/cooling circuit is only used to provide cooling in the corresponding room .
-- --
The selected heating/cooling circuit is only used to provide heating and cooling in the corresponding room .
Further information on the control type for the selected heating CIrCUit ( ~ Control types for the heating
system, page 20)
Maximum flow temperature
I
Fine adjustment of the heating curve that is preset via the heating system (~ Set the heating system and
heating curve for weather-compensated control, page 20)
----~~--~----------~
Table 27 Settings in menu heating/cooling circuit 1 . .. 4

Bosch HPC 400 Specifications

General

Brand	Bosch
Model	HPC 400
Category	Control Panel
Language	English