Bosch HPC 400 Installation Instructions For Contractors

§ BOSCH
5.2 System commissioning with the configuration wizard
The use r int e rface automatically recognises which BUS nod es are
installed in the syst e m. Configuration wizard adjusts the menu and the
factory defa u lts .
The system an a lysis may take up to one mi n ute.
C OMMI SS ION I NG
After the configuration wizard has performed th e sy st em an alysis, the
Commissioning menu is opened . The settings must be checked here
and , if necessary, adjusted and finally co n firmed .
If the system analysis is skipped, the Commissioning menu is open ed.
The settings listed here mu st be carefully adj u ste d according to the
installed system . Finally, the settings must be confirmed .
Further inf o rmati on on the settings refer to Cha pte r 6 st a rti ng on
page 10.
Select the corresponding country
~~~~~----------~--------------~--~------~~--------------~-----------
Buffer cylinder Is a buffer cylinder installed in the system? No I Yes
Start configuration wizard Start the configuration wizard? Yes I No
Select - a- dd . h- ea -t-a- ppliance ---- Which additional heat source is used ? --.- Not Installed I Add . electric heater In series I
I Add . heater with mixer only I Add . heater with
I
I
mixer in parallel I Hybrid
1
)
I
Mono mode I Sifllle energy source I Dual mode
Mixed add . heat. interface
Add . el. heater op. mode
___ _ __ _ __ __ __ __ ---l alternative I Dual mode parallel I Hybrid 2 ~
How is the mixing valve controlled for the auxiliary heater with mixerfunction? On /Off 10-10 V N-
I
How is the electric booster heater to be operated?
Is heating/cooling circuit 1 i nstalled? Where is heating circuit 1 electrically
connected?
Reduced 1.0 I Reduced 2.0 I Reduced 3.0 I
4Step
No I On the heat appliance I At the module
I Heating circuit 1 i nstalled
Is heating/cooling circuit 1 a heating circuit without mixing valve that is
No HCl on heat appfiance I No own heating I
Config HC1 at appliance
I
I
connected to the device?
circuit pump I Via pump PCl
Priority hHtiDa circu it l
Do the mode of operation and flow temperature in heating circoit 1 determine ; Yes l No
I
how the other heating circuits are operated?
Mixer heating circuit 1 Is heating/cooling circuit 1 a heating/cooling circuit with mixing valve? Yes I No
I
Mixer runtime heat eirc . 1 I How long does it take for the mixing valve in heati n g/cooling circuit 1 to rotate T
0 ... 6005
I
from one stop to the other? I
Heating system heat eirc . 1 What type of heating does heating/cooling circuit 1 handle?
Radiator I Convector heater I Underfloor
I
Ctrl type h. cir c. 1 How should the temperature influenced by heating circuit 1 be controlled?
Outdoor - temp . -compensated I Outside temp .
with
low end
Prog . unit Heat . circ. 1 What user interface or remote control is i nstalled for heating/cooling circuit 1? I
HPC400 I CR 10 I CR 10 H
Heating circuit 2 i nstalled , .. .
As for heating circuit 1
Heating circuit 3 installed, ...
r--
As for heating ci r cuit 1
~
H' - i ~ lied -
----- ----- ----
-
---
-
--
- -
eating c rcult Insta , ... As for heating circuit 1
,
DHWsystem
Is a DHW system insta ll ed?
--------l-
On I Off
t------ --
-- --
-
--
--
---
-
DHW heat pump 1 At which heat pump is DHW heating to be activated if two heat pumps are
On I Off
I ( DHW heat pump 2)
in
stalled?
----
--- ----
- t---- -- -- - ---- --
~~-
-
----
------
DHW ci rc.pump installed
Is a DHW circulation pump installed in the DHW system? No I Yes
f Solar thermal sys i nstalled
Is a solar system insta ll ed? No I Yes
--- ----
- --
--
---- --
-- -l
-- --
-- --
Fixed temperature The Heating system is connected directly to the DHW cylinder and the heating Off I On
I tempera t ure is controlled with a mixing valve . The heat pump will maintain a
I
constant temperature.
105 ... 60005 Pool mixing valve Is a diverter valve installed for heating the swimming pool? How long does it
I
take for the diverter valve to switch from one end to the other?
~ E _ lect __ r ~ . _ an _ od __ e _ in _ cyl ~ in _ de __ r ____ -+ ______ ~_- __ ls _ an ~ i _ ne _ rt _ a _ n ~ od-_- e ~ i _ n - s~ta _ lI _ ed __ in _ th _ e ~ D ~ H _ W ~ - c ~ y _ lin _ d ~ er? ~. ________ -+ ____________ Yes I No
~ F ~ u _ se ~ s _ iz _ e ______ ~ ______ ~ __________ A _ tw ~ h _ a _ tc _ u _ rr ~ e ~ nt ~ is ~ t ~ he ~ s ~ y ~ st ~ em ~ '~ s ~ fu ~ se ~ t ~ ri ~ ~ ~ e _ rro ~ ? ________ -+ ______ ~ 1 ~ 6 ~ A ~ 1 20 ~ A ~1 2 ~ 5 ~ A ~ 1 3 ~ 2 ~ A ~----~
Confirm configurati on Do the settings match with the installed system? Confirm I Back __ _
Table 11 Se ttings in the Co mmissioning menu
1) Not available if Germany is set as the country .
2) Only available if Germany is set as the country .
The DHW system is activat ed by de fault when delivered.
If no DHW system is ins t alled, but one is activa t ed , the
u se r interface i ndi ca te s a fau l t.
~ If no DHW sys t em is installed in the system,
de activa te t he DHW system in the Commi ss io ni ng or
DHWm e nu.
~PC 100-1~ '1()f;!l fllllnl 0' 9
AI

Bosch HPC 400 Specifications

General

Brand	Bosch
Model	HPC 400
Category	Control Panel
Language	English