BTECH DMR-6X2 User Manual

BTech DMR-6X2 CodePlug Programming Guide
V-1.00/1.00
Page 1 of 30
© 2017/8 Trygve Svärd KD0PNQ
INTRODUCTION
The BTech DMR-6X2 radio is a Dualband VHF and UHF radio with
both Digital DMR (Tier I and II) and Analog capabilities. It offers 4,000
channels (Analog and Digital), 10,000 Digital Talk Groups, and up to
150,000 contacts, as well as multiple DMR ID numbers (Radio ID’s)
for a single radio. With the enhanced capabilities of the DMR-6X2
radio, this Programming Guide will help users to understand all
aspects of how to program and set up the radio for maximum
usability.
Some of the extended features described include:
- Simplex Repeater (Digital Mode)
- Talk Group change (on-the-fly)
- Priority Channel Scanning
These are described in Section 6
Please note that the DMR-6X2 radio may have a locked key-board upon arrival. The
FCC requires per 47CFR90.203 that an unauthorized user shall not be able to enter
frequencies or transmit on an unauthorized frequency. Frequencies should only be
entered by service or maintenance personnel. This Guide is provided for such service
or maintenance personnel. To unlock keypad, press the “Menu” key and the “*” (star)
key.
The programming software (CPS) creates a file that contains the frequencies and
operating parameters is called a “codeplug”. Creating a codeplug is a ‘bottom up’
process where the lowest (common) elements must be created first, then built upon
until a fully functional codeplug has been created. The DMR-6X2 software can both
create the codeplug and write it to the radio. This software (also called CPS) has the
capability of both “importing” and “exporting” large data files, such as contact names.
1.0 GETTING STARTED
The programming cable for the DMR-6X2 radio is typically provided by
BTech. The USB cable required programming cable has a two pin ‘K-1’
connector.
There is no circuitry inside the cable. Similar appearing cables with
circuitry inside the cable will not work. Make sure the computer has the
correct driver for the cable – see the Device Manager on your PC.

BTECH DMR-6X2 Specifications

General

Frequency Range	136-174 MHz, 400-480 MHz
Channels	4, 000
Zones	250
Digital Protocol	DMR Tier I & II
IP Rating	IP54
GPS	Yes
Bluetooth	No
Modes	Analog and Digital
Display	Color LCD
Operating Mode	Simplex

Summary

Introduction to the BTech DMR-6X2

Getting Started with DMR-6X2 Programming

Step 1: Configuring Talk Groups

Talk Group Population Methods

Explains methods to populate talk groups, including manual entry and CSV import/export.

Step 2: Setting Up Digital Contacts

Digital Contact List Setup

Guides on downloading and importing DMR ID database for contact information display.

Step 3: Adding Your DMR Radio ID

Entering Your DMR Radio ID

Details the process of registering for and entering a unique DMR ID into the CPS.

Step 4: Creating Scan Lists

Scan List Creation and Management

Covers creating, naming, and populating scan lists with up to 50 channels.

Step 5: Organizing Channels into Zones

Zone List Setup and Re-sequencing

Guides creating logical groups (zones) of channels and re-sequencing them.

Step 6: Setting Up Receive Group Calls

Receive Group Call List Configuration

Sets up receive group lists to listen to additional TGs on a channel.

Step 7: Configuring Channels and Frequencies

Channel Parameter Configuration

Defines various parameters for channel configuration, including frequencies, power, and bandwidth.

Step 8: Configuring Optional Settings

Work Mode and VOX Settings

Configures radio display, VFO/MEM selection, VOX sensitivity, and delay.

FM, Power Save, and Key Function Settings

Manages FM mode, power saving features, and programmable key assignments.

Volume and Audio Settings

Audio Output Adjustments

Adjusts maximum volume, headphone volume, and microphone gain for optimal audio.

Other Setup Options

Alarm Setting Configuration

Sets up analog and digital alarm parameters, including emergency and man-down functions.

Creating Analog Zones and Channels

Analog Zone and Channel Creation

Guides creating zones for analog channels and assigning scan lists.

Step 9: Analog Address Book Setup

Analog Address Book Setup

Configures addresses for analog mode, referencing DTMF or 5Tone numbers.

Step 10: Prefabricated SMS Messages

Pre-written SMS Message Storage

Allows creating and storing pre-written SMS messages for digital contacts.

Step 11: Encryption Code Usage

Encryption Code Usage Note

Advises that this function should not be used in the USA.

Step 12: Alarm Setting Configuration

Alarm System Parameters

Configures analog and digital alarm parameters, including emergency and man-down functions.

Step 13: Hot Key Programming

Hot Key Functionality

Explains how hot keys provide quick access to radio functions.

Step 14: Analog Programming

Analog Channel Type Selection

Guides selecting 'A-Analog' for programming analog channels and disabling digital fields.

Final Step: Writing Codeplug to Radio

Codeplug Writing Process

Details the procedure for writing the configured codeplug to the radio.

Tool Menu Features

Tool Menu Features Overview

Lists features accessible via the TOOL menu, including import/export and firmware updates.

Record Functionality

Radio Recording Functionality

Explains how to use the radio's recording feature for conversations.

Import and Export Data

Data Import and Export via Spreadsheet

Describes using Excel for importing/exporting programming features and data.

Mode Selection Settings

Mode Selection for Channel/Contact Names

Allows non-identical channel and contact names, useful for repeater coverage.

Extended Talk Group Settings

Extended Talk Group Display Settings

Configures displayed Talk Group information on the LCD during reception.

Firmware Updates

Radio Firmware Update Procedure

Guides the process of updating the radio's firmware for new features.

Start-Up Screen Image Customization

Customizing the Boot Image

Explains how to replace the radio's start-up boot image.

Default Channel Information

Accessing Default Channel Information

Provides access to the first channel in the channel list for review.

Exporting Data Conversion Files

Exporting Codeplug Data

Exports codeplug data to a .dcf format for manipulation in Contact Manager.

Radio Model Information

Radio Model and Frequency Range Information

Displays available frequency range options for the radio model.

Radio LCD Display Indicators

Understanding LCD Display Indicators

Explains the various icons and information displayed on the radio's LCD screen.

DMR-6X2 Radio Firmware Update

Firmware Update Procedure Overview

Details the steps required to update the radio's firmware for new features.

Radio Total System Reset

System Reset Procedure and Warnings

Outlines the total system reset procedure and important precautions.

Rare Firmware Update Icon

Rare Firmware Update Note

Highlights a rare but potentially necessary firmware update procedure.

CPS Programmer Helper for DMR-6X2

CPS Programmer Overview

Introduces the CPS programmer software for managing radio data and settings.

Uploading DMR Database

Details the process of uploading the formatted DMR ID database to the software.

Special Functions in DMR-6X2

Extended Function List

Lists special extended functions available on the DMR-6X2 radio.

Digital Simplex Repeat Function

Digital Simplex Repeater Setup

Guides setting up the radio to function as a Store and Forward Simplex Repeater.

Digital Simplex Repeater Operation

Explains how to operate the radio in Digital Simplex Repeater mode.

On-the-Fly Talk Group Selection

Talk Group Selection Procedure

Describes how to switch talk groups quickly using the keypad, especially for hotspots.

Talk Group Operation Modes

Explains operation modes and hold time options for talk group selection.

GPS Ranging Functionality

GPS Ranging Functionality

Details how the "Ranging" key displays caller information and GPS data.

Priority Channel Scanning

Priority Channel Scanning Setup

Guides setting up priority channels within a scan list for enhanced scanning.