Cattron Safe-E-Stop - Using the Configuration Tool

85 pages

Save Page as PDF

To Next Page

To Previous Page

Version 17

Safe-E-Stop™

User Guide

A.4 Using the Configuration Tool

Launch Application

Launch the application and set the supervisor password. Note that if this password is lost, the application will

need to be re-installed.

Configuring Devices (Frequency)

The configure device screen will appear. Power up the PSD or MSD.

Main Page

Default Chapter2
- Communication Loss Recovery Stage2
- Table of Contents3
1 Introduction8
- Terminology8
2 Warnings and Cautions9
- MSD Wiring9
- Verification of Correct Device9
- Verification of Correct Linking9
- Placement of PSD in Charger9
- No Serviceable Parts10
- Regulatory Compliance10
- Awareness of PSD Range and Hazards Around the Machine10
- The System May Cause an Unexpected Stop of the Machine11
- The Safety Analysis Shall Consider the Reaction Time of the System11
- Ethernet May Not be Used for Safety-Critical Function11
- Frequency Change11
- Master Address Usage11
- General Safety Information11
- Intended Use12
- Improper Use12
- Equipment Rating Warning13
- Equipment Installation13
- Configuration Changes13
3 Operating Principle14
- General14
- Radio Transmission14
  - Continuous Transmission14
  - Radio Interference14
- Telegram Security15
4 Frequency Selection16
- Rules for Frequency Selection16
- Site Planning17
5 PSD and MSD Configuration Parameters18
- PSD Configuration18
- MSD Configuration19
- Configuration Part Number20
  - PSD Configuration20
  - MSD Configuration20
6 Psd21
- PSD Overview21
- PSD Status Indications21
  - PSD Leds22
- Joining an E-Stop Group23
- Normal Operation26
- Leaving an E-Stop Group27
- Switching off the PSD27
- Charging the Battery27
  - Battery Capacity and Operating Life27
- PSD Belt Clip28
7 Battery Chargers30
- General Information30
- Caution30
- Single Bay Charger31
- Six-Bay Charger31
- Battery Charger Status and Indicators33
8 Msd34
- MSD Overview34
- MSD Connections35
- MSD Status Indicators40
  - MSD Leds41
  - Msd Lcd41
- MSD Operational States41
- MSD Information and Setup42
- MSD Ethernet Address Configuration43
  - Ethernet Telegram Content44
- MSD Operation44
- MSD Installation44
9 System Commissioning50
10 System Decommissioning51
11 Parts Lists52
- Part Numbers52
12 Maintenance54
- PSD Maintenance54
- MSD Maintenance55
- Spare MSD55
Appendix A: PSD and MSD Configuration56
- General56
- Benefits of Using the Configuration Tool56
  - Master Address Change56
- Installing the Configuration Tool57
- Using the Configuration Tool58
Appendix B: RF Channel Number Vs Operating Frequency68
- Band B (433-434Mhz)68
  - Band B Channel Spacing Rules68
- Band D (450-470Mhz)68
  - Band D Channel Spacing Rules68
- Band F (902-927Mhz)68
  - Band F Channel Spacing Rules68
- Band J (929Mhz)69
  - Band J Channel Spacing Rules69
Appendix C: Approvals and Compliance Notifications70
- FCC Caution70
- EU Caution70
- Equipment Rating70
- Declaration of Conformity70
Appendix D: Ethernet Configuration & Data Mapping71
- Ethernet/Ip71
- Modbus TCP Configuration74
- PROFINET Configuration76
- Electronic Data Sheet (GSD File)76
Appendix E: Troubleshooting79
- Communication Losses79
- Psd80
- Msd81
- Battery Charger81
Appendix F: Technical Data and Specifications PSD and MSD82
Appendix G: Technical Data and Specifications Battery Charger82
Appendix H: Safety Manual for Safe-E-Stop83
- Functions83
- Failure Modes83
  - Psd83
  - Msd83
- Operational Constraints83
Appendix I: Safety Performance Level85

Cattron Safe-E-Stop - Using the Configuration Tool

Table of Contents