Chuango B11 - System Access and Siren Configuration; Access Code Management

1
2
3
4
5
All the alarm panels are with default user code, admin code and duress code. Please
change all codes before using and keep your codes secret.
Access Code
Admin Code
With admin code, user can arm and disarm, make system settings as well as reset codes
etc.
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose “Access Code”, press .[ ] [ ] [Enter]
Press or , choose “Admin Code”, press .[ ] [ ] [Enter]
LCD display will show “Input 6 Digits”, then input 6 digits for code, press [Enter].
(Default Admin Code: 123456)
Input the new admin code, press .[Enter]
With user code, user can set arm, home mode and disarm the alarm system.
User Code
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose “Access Code”, press .[ ] [ ] [Enter]
Press or , choose “User Code”, press .[ ] [ ] [Enter]
LCD display will show “Input 4 Digits”, then input 4 digits for code, press . [Enter]
(Default User Code: 1234)
Input the new user code, press .[Enter]
Duress Code
In case of emergency, when user is violently requested to disarm the system, it's
recommended to use the duress code to disarm the alarm system. The panel will
silently dial alarm telephone numbers stored.
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose “Access Code”, press .[ ] [ ] [Enter]
Press or , choose “Duress Code”, press .[ ] [ ] [Enter]
LCD display will show “Input 4 Digits”, then input 4 digits for code, press . [Enter]
(Default Duress Code: 1111)
Input the new duress code, press .[Enter]
Ringing Times for Remote Phone Control
After the set ringing times, user can make system settings from remote calling, such as
arming/disarming the system.
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose “Ringing Times”, press .[ ] [ ] [Enter]
Input 5~9 for ringing times, press .[Enter]
Default setting is 5 times.
Alarm Message
User can leave a 10-second voice message when control panel makes call to user's
stored phone number, voice recording will be repeatedly played to notify the intrusion.
Record Alarm Message
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose “Alarm Message”, press .[ ] [ ] [Enter]
Press or , choose “Record”, press . [ ] [ ] [Enter]
LCD display will show “Record 10s Voice” to remind you of the 10 seconds voice
recording, press .[Enter]
Start voice recording for 10s until the system stops automatically, or press to [Enter]
stop recording.
Siren Setup
Users can turn on/off wired siren, wireless siren, built-in siren as arm/disarm beep and
set siren ringing time.
Wired Siren
Wired siren is connected to the control panel by wire.
Turn On/Off Wired Siren
Log on the menu, press or , choose “System Settings”, press .[ ] [ ] [Enter]
Press or , choose “Siren Setup”, press .[ ] [ ] [Enter]
Press or , choose “Wired Siren”, press .[ ] [ ] [Enter]
Press or , choose “Siren On/Off”, press .[ ] [ ] [Enter]
Press or , choose “On” or “Off”, press [ ] [ ] [Enter].
“On” is to turn on the wired siren; “Off” is to turn off the wired siren.
Default setting is “On”; the wired siren is on.
35
36
1
2
3
4
5
1
2
3
4
5
1
2
3
1
2
3
4
5
1
2
3
4
5